| поискавой системы для электроныых деталей |
|
ADP1053ACPZ-R7 датащи(PDF) 72 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADP1053ACPZ-R7 датащи(HTML) 72 Page - Analog Devices |
|
72 / 84 page ![]() ADP1053 Data Sheet Rev. A | Page 72 of 84 Table 107. Register 0xFE72—Balance Control Settings Bits Bit Name R/W Description 7 Channel selection for volt-second balance control R/W Setting this bit selects Channel A or Channel C for volt-second balance control. 0 = use Channel C for volt-second balance control. 1 = use Channel A for volt-second balance control. 6 Volt-second balance control limit R/W This bit sets the modulation limit on the duty cycles from the volt-second control circuit. 0 = maximum volt-second control modulation is ±160 ns. 1 = maximum volt-second control modulation is ±80 ns. These bits set the volt-second balance control loop gain. Bit 5 Bit 4 Volt-Second Balance Control Loop Gain 0 0 1 0 1 4 1 0 16 [5:4] Volt-second balance loop gain R/W 1 1 64 3 Sensing selection for current balance R/W Setting this bit selects CS1_A/CS1_B or CS2_A/CS2_B for current balance control. 0 = use CS2_A/CS2_B for current balance control. 1 = use CS1_A/CS1_B for current balance control. 2 Current balance control limit R/W This bit sets the modulation limit on the duty cycles from the current control circuit. 0 = maximum current control modulation is ±160 ns. 1 = maximum current control modulation is ±80 ns. These bits set the current balance control loop gain. Bit 1 Bit 0 Current Balance Control Loop Gain 0 0 1 0 1 4 1 0 16 [1:0] Current balance loop gain R/W 1 1 64 TEMPERATURE SENSE AND PROTECTION SETTING REGISTERS Table 108. Register 0xFE73—RTD1 Gain Trim Bits Bit Name R/W Description 7 Gain polarity R/W 1 = negative gain is introduced. 0 = positive gain is introduced. [6:0] RTD1 gain trim R/W This value calibrates the RTD1 sensing gain (see the RTD1, RTD2, OTP1, and OTP2 Trim section). Table 109. Register 0xFE74—RTD2 Gain Trim Bits Bit Name R/W Description 7 Gain polarity R/W 1 = negative gain is introduced. 0 = positive gain is introduced. [6:0] RTD2 gain trim R/W This value calibrates the RTD2 sensing gain (see the RTD1, RTD2, OTP1, and OTP2 Trim section). |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |