ADP1053ACPZ-R7 datasheet(32/84 Pages) AD

32 / 84 page

ADP1053

Data Sheet

Rev. A | Page 32 of 84

POWER SUPPLY CALIBRATION AND TRIM

The ADP1053 allows the entire power supply to be calibrated

and trimmed digitally in the production environment. It can

calibrate items such as output voltage and trim for tolerance

errors introduced by sense resistors, current transformers, and

resistor dividers, as well as for its own internal circuitry. The part

comes factory trimmed, but it can be retrimmed by the user to

compensate for the errors introduced by external components

in the system.

To unlock the trim registers for write access, write to the

TRIM_PASSWORD register (Command 0xD6). Write the

trim password twice (the factory default password is 0xFF).

The trim registers are Register 0xFE10 through Register 0xFE17,

0xFE73, Register 0xFE74, Register 0xFE77, and Register 0xFE7C

through Register 0xFE7F. For complete information about these

registers, see the Manufacturer-Specific Extended Command

CS, CS1_A, AND CS1_B GAIN TRIM

To calibrate the CS, CS1_A, and CS1_B ADCs, 1 V is applied

between the CS/CS1_A/CS1_B pin and AGND. The CS/CS1_A/

CS1_B gain trim register (Register 0xFE6E, Register 0xFE10, or

CS1_B value in the appropriate value register reads 2560 decimal

(0xA00). The CS, CS1_A, and CS1_B value registers are Register

0xFED0, Register 0xFED1, and Register 0xFED2, respectively.

CS2_A AND CS2_B OFFSET AND GAIN TRIM

CS2_A and CS2_B Offset Trim

Offset errors are caused by the combined mismatch of the external

level-shifting resistors and internal current sources. The offset

trim has both an analog and a digital component. With 0 V at

the CS2 input, the desired ADC reading is 0 LSB.

The analog offset trim is performed to achieve a differential input

voltage of 0 V. The digital offset trim is performed to achieve an

ADC reading of 0 LSB. It is important to perform the offset trim

in the following order.

Select high-side or low-side current sensing using

Set the digital offset trim setting to 0x00 using Register

0xFE14 or Register 0xFE15.

Adjust the CS2 analog offset trim value (Register 0xFE16 or

Increase the CS2 digital offset trim register value (Register

0xFE14 or Register 0xFE15) until the CS2 value in Register

0xFED3 or Register 0xFED4 reads 0.

The offset trim is now complete. With 0 V at the CS2 input, the

ADC code now reads 0.

CS2_A and CS2_B Gain Trim

The gain trim removes any errors introduced by the sense

resistor tolerance.

Apply a known current (IOUT) across the sense resistor.

Adjust the CS2 gain trim value in Register 0xFE12 or

CS2 Value = IOUT × RSENSE × (4096/120 mV)

where RSENSE is the sense resistor value.

For example, if IOUT = 4.64 A and RSENSE = 20 mΩ,

CS2 Value = 4.64 A × 20 mΩ × (4096/120 mV) = 3168

(decimal).

The CS2 circuit is now trimmed. After the current sense trim is

performed, the OCP limits and settings should be configured.

VS_A AND VS_B GAIN TRIM

The voltage sense inputs are optimized for sensing signals at 1 V

and cannot sense a signal greater than 1.5 V. In a 28 V system, a

resistor divider is required to reduce the 28 V signal to below

1.5 V. It is recommended that the 28 V signal be reduced to 1 V

for best performance. The resistor divider can introduce errors,

which need to be trimmed.

The ADCs output a digital word of 2560 decimal (0xA00) when

there is exactly 1 V at their inputs.

ACSNS GAIN TRIM

The voltage sense inputs are optimized for ACSNS pin signals

at 1 V and cannot sense a signal greater than 1.5 V. A resistor

divider is required to reduce the sensed voltage signal to below

1.5 V. It is recommended that the ACSNS voltage signal be

reduced to 1 V for best performance. The resistor divider can

introduce errors, which need to be trimmed.

The following procedure should be used:

Apply nominal voltage at the sense point to achieve a

voltage of approximately 1 V at the ACSNS pin.

Adjust the ACSNS gain trim register (Register 0xFE77)

until the ACSNS reading in Register 0xFED9 is 0x500

(1280 decimal).

ADP1053ACPZ-R7 датащи(PDF) 32 Page - Analog Devices

ADP1053ACPZ-R7 датащи(HTML) 32 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84

датащи скачать

ссылки URL