MT9072AB datasheet(64/275 Pages) ZARLINK

64 / 275 page

MT9072

Data Sheet

Zarlink Semiconductor Inc.

8.0

Signaling

8.1

T1 Signaling

8.1.1

T1 Robbed Bit Signaling

When global control bit RBEn (Y04, Bit 8) is high the MT9072 will insert ABCD or AB signaling bits into bit 8 of

every transmit DS0 every 6th frame if the corresponding per channel Clear Channel bit(CC) is turned off. For the

transmitter Robbed bit signaling can be turned off on a per channel basis by setting CC bit in per timeslot control

24 (ABCD) will be loaded into an internal storage RAM. The transmit AB/ ABCD signaling nibbles can be set either

via the microport or through related channels of the CSTi serial links, see

ST-BUS vs. PCM24 Channel

Relationship in Tables 1 to 2. If the MPST bit is set in the Per Timeslot Control register(Y90-YAF), the transmit

signaling is sourced from the microport and not updated from the CSTi channel. If the MPST bit is not set, any

values written to the transmit signaling memory will be overwritten by the CSTi stream.

The receive signaling bits are stored in an internal RAM. These bits can be sourced to the CSTo streams. The serial

control streams that contain the transmit / receive signaling information (CSTi and CSTo respectively) can be

clocked at 2.048 MHz, or 8.192 MHz (global control0 register 900). In the case of 8.192 MHz the signaling from

framers 0 to 3 are sent and received by CSTi0/CSTo0 and framer 4 to 7 are sent and received on CSTi4/CSTo4.

The selection of the CSTi/CSTo interface is done by the number of signaling channels to be transmitted / received =

24 (timeslots) x 4 bits per timeslot (ABCD) = 24 nibbles. This leaves many unused nibble positions in the

2.048 MHz CSTi / CSTo bandwidth. These unused nibble locations are tristated. The usage of the bit stream is as

follows: the signaling bits are inserted / reported in the same CSTi / CSTo channels that correspond to the DS1

channels used in DSTi / DSTo - see Table 1 to 2. The ABCD are in the least significant nibble of each channel.

Unused nibbles and timeslots are tristate. In order to facilitate multiplexing on the CSTo control stream, an

additional control bit CSToEn (bit 1 of the interrupt and IO Control Word YF1) will tristate the whole stream when set

low. This control bit is forced low when the reset pin is asserted. In the case of D4 trunks, only AB bits are reported.

The control bits SM1-0(Register Y04) allow the user to program the 2 unused bits reported on CSTo in the signaling

nibble(for D4 Mode) otherwise occupied by CD signaling bits in ESF trunks.

A receive signaling bit debounce of 6 msec can be selected (RSDB set high - bit 6 of the signaling Control Word

Y04) for all T1 Modes.

If multiframe synchronization is lost (Synchronization and Alarm Status Word(Y10) Bit 12, MFSYNC = 1), the

receive signaling bits are frozen. They will become unfrozen when multi - frame synchronization is acquired (this is

the same as terminal frame synchronization for ESF links).

When the CASRI interrupt is unmasked, IRQ will become active when a signaling state change is detected in any of

the 24 receive channels and a selectable 1 msec, 4 msec or 8 msec timer (Y04 bit 0,1) has expired. This function

helps to reduce the frequency of interrupts generated due to signaling changes. For instance if 7 channels had a

signaling change only one interrupt will be generated in a 2, 8, or 16 msec duration. Upon an interrupt the user has

to read the CAS registers (Y70 to Y87)t o determine the channels with a signaling change.The CASRIM interrupt

mask is located in register Y45 bit 2 (reset low to enable interrupt); and the CASRI interrupt status bit in register is

Y35 bit 2. Any channels marked as clear channels will not generate an interrupt due to changes in ABCD bits.

When bit 0 (CC) in the per timeslot control word (Y90 to YA7) is set no bit robbing for the purpose of signaling will

occur in this channel and no signaling change interrupts will be generated by the channel. When bit 7 (MPST) is

set, the transmit signaling for the addressed channel can only be programmed by writing to the transmit signaling

page (Y50 to Y67) via the microport. If MPST is zero, the transmit signaling information is constantly updated with

the information from the equivalent channel on CSTi.

MT9072AB датащи(PDF) 64 Page - Zarlink Semiconductor Inc

MT9072AB датащи(HTML) 64 Page - Zarlink Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL