 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
LPC55S6X датащи(PDF) 38 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
LPC55S6X датащи(HTML) 38 Page - NXP Semiconductors |
|
|
38 / 128 page  LPC55S6x All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2020. All rights reserved. Product data sheet Rev. 1.9 — 10 February 2020 38 of 128 NXP Semiconductors LPC55S6x 32-bit ARM Cortex-M33 microcontroller 6.1.1 Termination of unused pins Table 4 shows how to terminate pins that are not used in the application. In many cases, unused pins should be connected externally or configured correctly by software to minimize the overall power consumption of the part. Unused pins with GPIO function should be configured as outputs set to LOW with their internal pull-up disabled. To configure a GPIO pin as output and drive it LOW, select the GPIO function in the IOCON register, select output in the GPIO DIR register, and write a 0 to the GPIO PORT register for that pin. Disable the pull-up in the pin’s IOCON register. In addition, it is recommended to configure all GPIO pins that are not bonded out on smaller packages as outputs driven LOW with their internal pull-up disabled. [1] I = Input, IA = Inactive (no pull-up/pull-down enabled), PU = Pull-Up enabled Table 4. Termination of unused pins Pin Default state[1] Recommended termination of unused pins RESET I; PU The RESET pin can be left unconnected if the application does not use it. all PIOn_m (not open-drain) I; PU Can be left unconnected if driven LOW and configured as GPIO output with pull-up or pull-down disabled by software. PIOn_m (I2C open-drain) IA Can be left unconnected if driven LOW and configured as GPIO output by software. XTAL32K_P - Connect to ground. When grounded, the RTC oscillator is disabled. XTAL32K_N - Can be left unconnected. XTAL32M_P - Connect to ground. When grounded, the RTC oscillator is disabled. XTAL32M_N - Can be left unconnected. VREFP - Tie to VBAT_DCDC. VREFN - Tie to VSS. VDDA - Tie to VBAT_DCDC. VSSA - Tie to VSS. USBn_DP F Can be left unconnected. USBn_DM F Can be left unconnected. USBn_3V3 F Tie to VBAT_DCDC. USB1_VBUS F Tie to VBAT_DCDC. USBn_VSS F Tie to VSS. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
