ADP1052ACPZ-R7 datasheet(84/113 Pages) AD

84 / 113 page

ADP1052

Data Sheet

Rev. B | Page 84 of 113

Table 119. Register 0xFE0C—Volt-Second Balance Blanking and SR Disable During Soft Start

Bits

Bit Name/Function

R/W

Description

[7:5]

Reserved

R/W

Reserved.

VIN_UV_FAULT reenable blank

R/W

0 = VIN_UV_FAULT flag is not blanked during the flag reenable delay. This is the

recommended setting if the input voltage signal can be sensed by the ADP1052 before the

PSU starts to operate.

1 = VIN_UV_FAULT flag is blanked during the flag reenable delay.

First flag ID update

R/W

This bit specifies whether the first flag ID is saved in the EEPROM. If it is set, the first flag ID

is saved in the EEPROM. During the VDD power reset, the first flag ID is downloaded from

the EEPROM to Register 0xFEA6.

0 = the first flag ID is not saved in the EEPROM.

1 = the first flag ID is saved in the EEPROM.

Flag shutdown timing

R/W

Specifies when the PWM outputs are shut down after a manufacturer specific flag is triggered.

0 = the PWM outputs are shut down at the end of the switching cycle.

1 = the PWM outputs are shut down immediately.

Volt-second balance blanking

R/W

0 = the volt-second balance control is not blanked during soft start.

1 = the volt-second balance control is blanked during soft start.

SR disable

R/W

0 = SR1 and SR2 are not disabled during soft start.

1 = SR1 and SR2 are disabled during soft start.

Table 120. Register 0xFE0D—PGOOD Mask Settings

Bits

Bit Name/Function

R/W

Description

VIN_UV_FAULT flag

R/W

1 = PGOOD ignores the VIN_UV_FAULT flag.

IIN_OC_FAST_FAULT flag

R/W

1 = PGOOD ignores the IIN_OC_FAST_FAULT flag.

IOUT_OC_FAULT flag

R/W

1 = PGOOD ignores the IOUT_OC_FAULT flag.

VOUT_OV_FAULT flag

R/W

1 = PGOOD ignores the VOUT_OV_FAULT flag.

VOUT_UV_FAULT flag

R/W

1 = PGOOD ignores the VOUT_UV_FAULT flag.

OT_FAULT flag

R/W

1 = PGOOD ignores the OT_FAULT flag.

OT_WARNING flag

R/W

1 = PGOOD ignores the OT_WARNING flag.

SR_RC_FAULT flag

R/W

1 = PGOOD ignores the SR_RC_FAULT flag.

Table 121. Register 0xFE0E—PGOOD Flag Debounce

Bits

Bit Name/Function

R/W

Description

CS1 cycle-by-cycle current limit

to disable OUTD

R/W

Setting this bit enables the CS1 cycle-by-cycle current limit to disable the OUTD output for the

remainder of the switching cycle when cycle-by-cycle current limiting occurs.

CS1 cycle-by-cycle current limit

to disable OUTC

R/W

Setting this bit enables the CS1 cycle-by-cycle current limit to disable the OUTC output for the

remainder of the switching cycle when cycle-by-cycle current limiting occurs.

CS1 cycle-by-cycle current limit

to disable OUTB

R/W

Setting this bit enables the CS1 cycle-by-cycle current limit to disable the OUTB output for the

remainder of the switching cycle when cycle-by-cycle current limiting occurs.

CS1 cycle-by-cycle current limit

to disable OUTA

R/W

Setting this bit enables the CS1 cycle-by-cycle current limit to disable the OUTA output for the

remainder of the switching cycle when cycle-by-cycle current limiting occurs.

[3:2]

PGOOD flag clearing debounce

R/W

These bits specify the PGOOD flag clearing debounce, which is the time from when the PGOOD

clearing condition is met to the time when the PGOOD flag is cleared.

Bit 3

Bit 2

PGOOD Flag Setting Debounce (ms)

200

320

600

[1:0]

PGOOD flag setting debounce

R/W

These bits specify the PGOOD flag setting debounce, which is the time from when the PGOOD

setting condition is met to the time when the PGOOD flag is set.

Bit 1

Bit 0

PGOOD Flag Clearing Debounce (ms)

200

320

600

ADP1052ACPZ-R7 датащи(PDF) 84 Page - Analog Devices

ADP1052ACPZ-R7 датащи(HTML) 84 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL