ADP1052ACPZ-R7 datasheet(31/113 Pages) AD

31 / 113 page

Data Sheet

ADP1052

Rev. B | Page 31 of 113

Manufacturer Specific Latched Flags

The ADP1052 has a set of latched flag registers (Register 0xFEA3

to Register 0xFEA5). The latched flag registers have the same flags

as Register 0xFEA0 to Register 0xFEA2, but the flags in the

latched registers remain set so that intermittent faults can be

detected. Reading a latched flag register resets all the flags in that

Flags Debounce Time

The debounce timing of the manufacturer specific flags and the

PMBus standard flags is programmable (see Table 6). The

debounce time is the time during which the fault condition

must be continuously triggered before the flag is set. Refer to

the corresponding register settings for more information.

The debounce time is used for flag setting. Only the PGOOD

flag has a debounce time for flag clearing. For all other flags,

the flag reenable delay, specified in Register 0xFE05[7:6] (see

Table 113), functions as the debounce time for flag clearing.

Refer to the Manufacturer Specific Protection Responses

section for details.

Housekeeping Flags

The CHIP_PASSWORD_UNLOCKED flag (Register 0xFEA0[7])

indicates that the chip password is in the unlocked state, and all

the registers can be accessed.

The VDD_OV flag (Register 0xFEA0[0]) is set when the VDD

voltage exceeds the VDD OVLO threshold. The debounce time is

programmable as 2 μs or 500 μs, using Register 0xFE05[4]. When

the flag is set, the ADP1052 shuts down. The flag is always cleared

when Register 0xFE05[5] is set, regardless of the VDD voltage.

The EEPROM_UNLOCKED flag (Register 0xFEA2[3]) indicates

that the EEPROM is in the unlocked state and can be updated.

The CRC_FAULT flag (Register 0xFEA2[2]) indicates that an error

has occurred when downloading the EEPROM contents to the

internal registers. The device shuts down and requires a PSON

signal (programmed in Register 0x01 and Register 0x02) and/or

the toggling of the CTRL pin (Pin 16) to restart.

Flag Blanking During Soft Start

Flag blanking means that when a fault condition is met, the

corresponding flag is set, but there are no related actions.

The following flags are always blanked during soft start:

•

VOUT_UV_FAULT

•

OT_FAULT

The following flags can be programmed to be blanked during soft

start, using Register 0xFE0B:

•

VOUT_OV_FAULT (Bit 0)

•

CS3_OC_FAULT (Bit 1)

•

IOUT_OC_FAULT (Bit 2)

•

IIN_OC_FAST_FAULT (Bit 3)

•

VIN_UV_FAULT (Bit 4)

•

LIGHT_LOAD (Bit 5)

•

DEEP_LIGHT_LOAD (Bit 5)

•

FLAGIN (Bit 6)

•

SR_RC_FAULT (Bit 7)

If a flag is blanked during soft start, it is also blanked during the

TON_DELAY time.

Table 6. Flag Debounce Time

Flag

Debounce Time

VOUT_OV_FAULT

0 μs, 1 μs, 2 μs, 8 μs

0xFE26[7:6]

VOUT_UV_FAULT

0 ms, 20 ms, 40 ms, 80 ms, 160 ms, 320 ms, 640 ms, 1280 ms

0x45[2:0]

IOUT_OC_FAULT

0 ms, 20 ms, 40 ms, 80 ms, 160 ms, 320 ms, 640 ms, 1280 ms

0x47[2:0]

OT_FAULT

1 sec

0x50[2:0]

OT_WARNING

0 ms, 100 ms

0xFE2F[2]

CS3_OC_FAULT

0 ms, 10 ms, 20 ms, 200 ms

0xFE19[6:5]

VIN_UV_FAULT

0 ms, 2.5 ms, 10 ms, 100 ms

0xFE29[1:0]

FLAGIN

0 μs, 100 μs

0xFE12[1]

SR_RC_FAULT

40 ns, 200 ns

0xFE1A[3]

VDD_OV

2 μs, 500 μs

0xFE05[4]

PGOOD

0 ms, 200 ms, 320 ms, 600 ms

0xFE0E[3:0]

ADP1052ACPZ-R7 датащи(PDF) 31 Page - Analog Devices

ADP1052ACPZ-R7 датащи(HTML) 31 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL