SC2200 datasheet(168/433 Pages) NSC

168 / 433 page

www.national.com

168

Revision 3.0

Core Logic Module (Continued)

SL1 Sleep State (ACPI S1)

In this state the core processor is in 3V Suspend mode (all

its clocks are stopped, including the memory controller and

thedisplay controller). TheSDRAM isplacedinself-refresh

mode. All other SC2200 system clocks and PLLs are run-

ning. All devices are powered up (PWRCNT[2:1] and

ONCTL# are all asserted). See Section 5.2.9.5 "Usage

Hints" on page 170.

No reset is performed, when exiting this state. The SC2200

keeps all context in this state. This state corresponds to

ACPI Sleep state S1.

SL2 Sleep State (ACPI S1)

In this state, all of the SC2200 clocks are stopped including

the PLLs. Selected clocks from the PLLs can be kept run-

ning under program control (F0 Index 60h). An exception to

this is the CLK32 output signal which keeps toggling and

the 32 KHz oscillator itself. The SDRAM is placed in self-

refresh mode. The PWRCNT1 pin is deasserted. The

SC2200 itself is powered up. The system designer can

decide which other system devices to power off with the

PWRCNT1 pin.

No reset is performed, when exiting this state. The SC2200

keeps all context in this state. This state corresponds to

ACPI sleep state S1, with lower power and longer wake

time than in SL1.

SL3 Sleep State (ACPI S3)

In this state, the SDRAM is placed in self-refresh mode,

and PWRCNT[2:1] are deasserted. PWRCNT[2:1] should

be used to power off most of the system (except for the

SDRAM). If the Save-to-RAM feature is used, external cir-

cuitry in the SDRAM interface is required to guarantee data

integrity. All SC2200 signals powered by VSB,VSBL or VBAT

are still functional to allow wakeup and to keep the RTC.

The power-up sequence is performed, when exiting this

state. This state corresponds to ACPI Sleep state S3.

SL4 and SL5 Sleep States (ACPI S4 and S5)

The SL4 and SL5 states are similar from the hardware per-

spective.

these

states,

the

SC2200

deasserts

PWRCNT[2:1] and ONCTL#. PWRCNT[2:1] and ONCTL#

should be used to power off the system. All signals pow-

ered by VSB,VSBL or VBAT are still functional to allow

wakeup and to keep the RTC.

Whileinthisstate,LED#can be toggledtogivevisualnoti-

fication of this state. ACPI Function Control register

(F1BAR1+I/O Offset 07h[7:6]) is used to control LED#.

The power-up sequence is performed when exiting this

state. This state corresponds to ACPI Sleep states S4 and

S5.

Table 5-5. Wakeup Events Capability

Event

S0/C1

S0/C3

SL1

SL2

SL3

SL4, SL5

Enabled Interrupts

Yes

SMI according to Table 5-8

Yes

SCI according to Table 5-8

Yes

GPIO[47:32], GPIO[15:0]

Yes

Power Button

Yes

Power Button Override

Yes

Bus Master Request

Yes1

Yes

---

Thermal Monitoring

Yes

USB

Yes

SDATA_IN2 (AC97)

Yes

IRRX1 (Infrared)

Yes

GPWIO[2:0]

Yes

RI2# (UART2)

Yes

RTC

Yes

Temporarily exits state.

SC2200 датащи(PDF) 168 Page - National Semiconductor (TI)

SC2200 датащи(HTML) 168 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL