SC2200 datasheet(88/433 Pages) NSC

88 / 433 page

www.national.com

Revision 3.0

General Configuration Block (Continued)

3.3

WATCHDOG

The SC2200 includes a WATCHDOG function to serve as a

fail-safe mechanism in case the system becomes hung.

When triggered, the WATCHDOG mechanism returns the

system to a known state by generating an interrupt, an

SMI, or a system reset (depending on configuration).

3.3.1

Functional Description

WATCHDOG is enabled when the WATCHDOG Timeout

(WDTO) register (Offset 00h) is set to a non-zero value.

The WATCHDOG timer starts with this value and counts

down until either the count reaches 0, or a trigger event

restarts the count (with the WDTO register value).

The WATCHDOG timer is restarted in any of the following

cases:

• The WDTO register is set with a non-zero value.

• The WATCHDOG timer reaches 0 and the WATCHDOG

Overflow bit, WDOVF (Offset 04h[0]), is 0.

The WATCHDOG function is disabled in any of the follow-

ing cases:

• System reset occurs.

• The WDTO register is set to 0.

• The WDOVF bit is already 1 when the timer reaches 0.

3.3.1.1

WATCHDOG Timer

The WATCHDOG timer is a 16-bit down counter. Its input

clock is a 32 KHz clock divided by a predefined value (see

WDPRES field, Offset 02h[3:0]). The 32 KHz input clock is

enabled when either:

• The GX1 module’s internal SUSPA# signal is 1.

• The GX1 module’s internal SUSPA# signal is 0 and the

WD32KPD bit (Offset 02h[8]) is 0.

The 32 KHz input clock is disabled, when:

• The GX1 module’s internal SUSPA# signal is 0 and the

WD32KPD bit is 1.

For more information about signal SUSPA#, refer to the

GX1 Processor Series Datasheet.

When the WATCHDOG timer reaches 0:

• If the WDOVF bit in the WDSTS register (Offset 04h[0])

is 0, an interrupt, an SMI or a system reset is generated,

depending on the value of the WDTYPE1 field in the

WDCNFG register (Offset 02h[5:4]).

• If the WDOVF bit in the WDSTS register is already 1

when the WATCHDOG timer reaches 0, an interrupt, an

SMI or a system reset is generated according to the

WDTYPE2 field (Offset 02h[7:6]), and the timer is

disabled. The WATCHDOG timer is re-enabled when a

non-zero value is written to the WDTO register (Offset

00h).

The interrupt or SMI is deasserted when the WDOVF bit is

set to 0. The reset generated by the WATCHDOG functio-

nis used to trigger a system reset via the Core Logic mod-

ule. Thevalue of theWDOVF bit, theWDTYPE1field,and

the WDTYPE2 field are not affected by a system reset

(except when generated by power-on reset).

TheSC2200alsoallows no action to be takenwhenthe

timer reaches 0 (according to WDTYPE1 field and

WDTYPE2 field). In this case only the WDOVF bit is set to

Figure 3-1. WATCHDOG Block Diagram

WDPRES

WDTO

Timer

WDOVF

WDTYPE1 or

WDTYPE2

Internal Fast-PCI Bus

32 KHz

POR#

WATCHDOG

Reset IRQ SMI

SUSPA#

SC2200 датащи(PDF) 88 Page - National Semiconductor (TI)

SC2200 датащи(HTML) 88 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL