ADP1055ACPZ-R7 datasheet(73/140 Pages) AD

73 / 140 page

Data Sheet

ADP1055

Rev. A | Page 73 of 140

Bits

Bit Name

R/W

Description

[5:3]

Retry setting

R/W

Number of retry attempts following a fault condition. A fault condition can be cleared by a reset,

a power-off/power-on sequence, or a loss of bias power.

Bit 5

Bit 4

Bit 3

Number of Retries

Infinite

[2:0]

Delay times

R/W

Number of delay time units (see Register 0xFE3E).

IIN_OC_FAULT_LIMIT

The IIN_OC_FAULT_LIMIT command sets the threshold value (in amperes) measured at the sense/input pin that causes an overcurrent

fault condition.

Table 58. Register 0x5B—IIN_OC_FAULT_LIMIT

Bits

Bit Name

R/W

Description

[15:11]

Exponent-N

R/W

Twos complement N-exponent used in linear data format (X = Y × 2N).

[10:0]

Mantissa-Y

R/W

Twos complement Y-mantissa used in linear data format (X = Y × 2N).

IIN_OC_FAULT_RESPONSE

The IIN_OC_FAULT_RESPONSE command instructs the device on actions to take due to an input overcurrent fault condition. The

device notifies the host and sets the OTHER bit in the STATUS_BYTE register, the INPUT bit in the STATUS_WORD register, and the

IIN_OC_FAULT bit in the STATUS_INPUT register.

Table 59. Register 0x5C—IIN_OC_FAULT_RESPONSE

Bits

Bit Name

R/W

Description

[7:6]

Response

R/W

Determines the device response to an input overcurrent fault condition.

Bit 7

Bit 6

Response

Operate in current limiting mode, maintaining the output current at

IOUT_OC_FAULT_LIMIT.

Operate in current limiting mode, maintaining the output current at

IOUT_OC_FAULT_LIMIT. If VOUT falls below the IOUT_OC_LV_FAULT_LIMIT,

respond as programmed by the retry setting (Bits[5:3]).

Continue operation in current limiting mode for the delay time (Bits[2:0]). If the

device is still in current limiting mode, respond as programmed by the retry

setting (Bits[5:3]).

Shut down, disable the output, and respond as programmed by the retry

setting (Bits[5:3]).

[5:3]

Retry setting

R/W

Number of retry attempts following a fault condition. A fault condition can be cleared by a reset,

a power-off/power-on sequence, or a loss of bias power.

Bit 5

Bit 4

Bit 3

Number of Retries

Infinite

[2:0]

Delay times

R/W

Number of delay time units (see Register 0xFE3E).

ADP1055ACPZ-R7 датащи(PDF) 73 Page - Analog Devices

ADP1055ACPZ-R7 датащи(HTML) 73 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL