XIO2001IPNP datasheet(128/145 Pages) TI2

128 / 145 page

• The inductor(s) associated with the filter must have a DC resistance low enough to pass the required current

for the connected power terminals. The voltage drop across the inductor must be low enough to meet the

minus 10% voltage margin requirement associated with each XIO2001 power terminal. Power supply output

voltage variation must be considered as well as voltage drops associated with any connector pins and circuit

board power distribution geometries.

• The Q versus frequency curve associated with the inductor must be appropriate to reduce power terminal

noise to less than the maximum peak-to-peak amplitude requirement for the XIO2001. Recommending a

specific inductor is difficult because every system design is different and therefore the noise frequencies and

noise amplitudes are different. Many factors will influence the inductor selection for the filter design. Power

supplies must have adequate input and output filtering. A sufficient number of bulk and bypass capacitors are

required to minimize switching noise. Assuming that board level power is properly filtered and minimal low

frequency noise is present, frequencies less than 10 MHz, an inductor with a Q greater than 20 from

approximately 10 MHz to 3 GHz should be adequate for most system applications.

• The series component(s) in the filter may either be an inductor or a ferrite bead. Testing has been performed

on both component types. When measuring PCI-Express link jitter, the inductor or ferrite bead solutions

produce equal results. When measuring circuit board EMI, the ferrite bead is a superior solution.

Note

The XIO2001 reference schematics include ferrite beads in the analog power supply filters.

• When designing filters associated with power distribution, the power supply is a low impedance source and

the device power terminals are a low impedance load. The best filter for this application is a T filter. See

Figure 9-12 for a T-filter circuit. Some system may require this type of filter design if the power supplies or

nearby components are exceptionally noisy. This type of filter design is recommended if a significant amount

of low frequency noise, frequencies less than 10 MHz, is present in a system.

• For most applications a Pi filter will be adequate. See Figure 9-12 for a Pi-filter circuit. When implementing a

Pi filter, the two capacitors and the inductor must be located next to each other on the circuit board and must

be connected together with wide low impedance traces. Capacitor ground connections must be short and low

impedance.

• If a significant amount of high frequency noise, frequencies greater than 300 MHz, is present in a system,

creating an internal circuit board capacitor will help reduce this noise. This is accomplished by locating power

and ground planes next to each other in the circuit board stackup. A gap of 0.003 mils between the power

and ground planes will significantly reduce this high frequency noise.

• Another option for filtering high-frequency logic noise is to create an internal board capacitor using signal

layer copper plates. When a component requires a low-noise power supply, usually the Pi filter is located

near the component. Directly under the Pi filter, a plate capacitor may be created. In the circuit board stack-

up, select a signal layer that is physically located next to a ground plane. Then, generate an internal 0.25 inch

by 0.25 inch plate on that signal layer. Assuming a 0.006 mil gap between the signal layer plate and the

internal ground plane, this will generate a 12 pF capacitor. By connecting this plate capacitor to the trace

between the Pi filter and the component’s power pins, an internal circuit board high frequency bypass

capacitor is created. This solution is extremely effective for switching frequencies above 300 MHz.

Figure 9-12 illustrates two different filter designs that may be used with the XIO2001 to provide lownoise power

to critical power pins.

XIO2001

SCPS212J – MAY 2009 – REVISED JANUARY 2021

www.ti.com

128

Submit Document Feedback

Product Folder Links: XIO2001

XIO2001IPNP датащи(PDF) 128 Page - Texas Instruments

XIO2001IPNP датащи(HTML) 128 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL