PIC16C71 datasheet(85/337 Pages) MICROCHIP

85 / 337 page

DS30234D-page 85

PIC16C6X

FIGURE 11-2: SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)

R/W-0

WCOL

SSPOV

SSPEN

CKP

SSPM3

SSPM2

SSPM1

SSPM0

R = Readable bit

W = Writable bit

U = Unimplemented bit,

read as ‘0’

- n =Value at POR reset

bit7

bit0

bit 7:

WCOL: Write Collision Detect bit

1 = The SSPBUF register is written while it is still transmitting the previous word

(must be cleared in software)

0 = No collision

bit 6:

SSPOV: Receive Overﬂow Detect bit

In SPI mode

1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overﬂow,

the data in SSPSR register is lost. Overﬂow can only occur in slave mode. The user must read the SSP-

BUF, even if only transmitting data, to avoid setting overﬂow. In master mode the overﬂow bit is not set

since each new reception (and transmission) is initiated by writing to the SSPBUF register.

0 = No overﬂow

In I2C mode

1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t care"

in transmit mode. SSPOV must be cleared in software in either mode.

0 = No overﬂow

bit 5:

SSPEN: Synchronous Serial Port Enable bit

In SPI mode

1 = Enables serial port and conﬁgures SCK, SDO, and SDI as serial port pins

0 = Disables serial port and conﬁgures these pins as I/O port pins

In I2C mode

1 = Enables the serial port and conﬁgures the SDA and SCL pins as serial port pins

0 = Disables serial port and conﬁgures these pins as I/O port pins

In both modes, when enabled, these pins must be properly conﬁgured as input or output.

bit 4:

CKP: Clock Polarity Select bit

In SPI mode

1 = Idle state for clock is a high level. Transmit happens on falling edge, receive on rising edge.

0 = Idle state for clock is a low level. Transmit happens on rising edge, receive on falling edge.

In I2C mode

SCK release control

1 = Enable clock

0 = Holds clock low (clock stretch) (Used to ensure data setup time)

bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits

0000

= SPI master mode, clock = Fosc/4

0001

= SPI master mode, clock = Fosc/16

0010

= SPI master mode, clock = Fosc/64

0011

= SPI master mode, clock = TMR2 output/2

0100

= SPI slave mode, clock = SCK pin. SS pin control enabled.

0101

= SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.

0110

= I2C slave mode, 7-bit address

0111

= I2C slave mode, 10-bit address

1011

= I2C firmware controlled Master Mode (slave idle)

1110

= I2C slave mode, 7-bit address with start and stop bit interrupts enabled

1111

= I2C slave mode, 10-bit address with start and stop bit interrupts enabled

Applicable Devices

61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67

PIC16C71 датащи(PDF) 85 Page - Microchip Technology

PIC16C71 датащи(HTML) 85 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL