PIC16C71 datasheet(80/337 Pages) MICROCHIP

80 / 337 page

PIC16C6X

DS30234D-page 80

10.3

PWM Mode

In Pulse Width Modulation (PWM) mode, the CCP1 pin

produces up to a 10-bit resolution PWM output. Since

the CCP1 pin is multiplexed with the PORTC data latch,

the TRISC<2> bit must be cleared to make the CCP1

pin an output.

Figure 10-4 shows a simpliﬁed block diagram of the

CCP module in PWM mode.

For a step by step procedure on how to set up the CCP

module for PWM operation, see Section 10.3.3.

FIGURE 10-4: SIMPLIFIED PWM BLOCK

DIAGRAM

A PWM output (Figure 10-5) has a time base (period)

and a time that the output stays high (duty cycle). The

frequency of the PWM is the inverse of the period

(1/period).

FIGURE 10-5: PWM OUTPUT

Applicable Devices

61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67

Note:

Clearing the CCP1CON register will force

the CCP1 PWM output latch to the default

low level. This is not the PORTC I/O data

latch.

CCPR1L

CCPR1H (Slave)

Comparator

TMR2

Comparator

PR2

(Note 1)

Duty cycle registers

CCP1CON<5:4>

Clear Timer,

CCP1 pin and

latch D.C.

TRISC2

RC2/CCP1

Note 1: 8-bit timer is concatenated with 2-bit internal Q clock

or 2 bits of the prescaler to create 10-bit time-base.

Period

Duty Cycle

TMR2 = PR2

TMR2 = Duty Cycle

TMR2 = PR2

10.3.1

PWM PERIOD

The PWM period is speciﬁed by writing to the PR2 reg-

ister. The PWM period can be calculated using the fol-

lowing formula:

PWM period = [(PR2) + 1] • 4 • TOSC •

(TMR2 prescale value)

PWM frequency is deﬁned as 1 / [PWM period].

When TMR2 is equal to PR2, the following three events

occur on the next increment cycle:

• TMR2 is cleared

• The PWM duty cycle is latched from CCPR1L into

CCPR1H

• The CCP1 pin is set (exception: if PWM duty

cycle = 0%, the CCP1 pin will not be set)

10.3.2

PWM DUTY CYCLE

The PWM duty cycle is speciﬁed by writing to the

CCPR1L register and to the CCP1CON<5:4> bits. Up

to 10-bit resolution is available: the CCPR1L contains

the eight MSbs and the CCP1CON<5:4> contains the

two LSbs. This 10-bit value is represented by

CCPR1L:CCP1CON<5:4>. The following equation is

used to calculate the PWM duty cycle in time:

PWM duty cycle = (CCPR1L:CCP1CON<5:4>) •

Tosc • (TMR2 prescale value)

CCPR1L and CCP1CON<5:4> can be written to at any

time, but the duty cycle value is not latched into

CCPR1H until after a match between PR2 and TMR2

occurs (i.e., the period is complete). In PWM mode,

CCPR1H is a read-only register.

The CCPR1H register and a 2-bit internal latch are

used to double buffer the PWM duty cycle. This double

buffering is essential for glitchless PWM operation.

When the CCPR1H and 2-bit latch match TMR2 con-

catenated with an internal 2-bit Q clock or 2 bits of the

TMR2 prescaler, the CCP1 pin is cleared.

Maximum PWM resolution (bits) for a given PWM

frequency:

Note:

The Timer2 postscaler (see Section 9.1) is

not used in the determination of the PWM

frequency. The postscaler could be used to

have a servo update rate at a different fre-

quency than the PWM output.

Note:

If the PWM duty cycle value is longer than

the PWM period the CCP1 pin will not be

forced to the low level.

log

(

FPWM

log(2)

FOSC

)

bits

PIC16C71 датащи(PDF) 80 Page - Microchip Technology

PIC16C71 датащи(HTML) 80 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL