MPC8610EC datasheet(83/96 Pages) FREESCALE

83 / 96 page

Hardware Design Considerations

MPC8610 Integrated Host Processor Hardware Specifications, Rev. 0

Freescale Semiconductor

software. However, if a SerDes port is enabled through the POR input the user can disable it through the DEVDISR register in

software. Disabling a SerDes port through software should be done on a temporary basis. Power is always required for the

SerDes interface, even if the port is disabled through either mechanism. Table 61 describes the possible enabled/disabled

scenarios for a SerDes port. The termination recommendations must be followed for each port.

If the high-speed SerDes port requires complete or partial termination, the unused pins should be terminated as described in this

section.

The following pins must be left unconnected (floating):

•SDn_TX[7:0]

The following pins must be connected to GND:

•SDn_RX[7:0]

•SDn_REF_CLK

•

SDn_REF_CLK

For other directions on reserved or no-connects pins, see Section 1.1, “Pin Assignments.”

3.11

Guidelines for PCI Interface Termination

PCI termination if PCI is not used at all.

Option 1

•

If PCI arbiter is enabled during POR,

— All AD pins will be driven to the stable states after POR. Therefore, all ADs pins can be floating. This includes

PCI_AD[31:0], PCI_C/BE[3:0], and PCI_PAR signals.

— All PCI control pins can be grouped together and tied to OVDD through a single 10-kΩ resistor.

— It is optional to disable PCI block through DEVDISR register after POR reset.

Table 61. SerDes Port Enabled/Disabled Configurations

Disabled through POR input

Enabled through POR input

Enabled through DEVDISR

SerDes port is disabled (and cannot

be enabled through DEVDISR)

Complete termination required

(Reference clock not required

SerDes port is enabled

Partial termination may be required1

(Reference clock is required)

1 Partial termination when a SerDes port is enabled through both POR input and DEVDISR is determined by the

SerDes port mode. If port 1 is in x4 PCI Express mode, no termination is required because all pins are being

used. If port 1 is in x1/x2 PCI Express mode, termination is required on the unused pins. If port 2 is in x8 PCI

Express mode, no termination is required because all pins are being used. If port 1 is in x1/x2/x4 PCI Express

mode, termination is required on the unused pins.

Disabled through DEVDISR

SerDes port is disabled (through

POR input)

Complete termination required

(Reference clock not required)

SerDes port is disabled after software

disables port

Same termination requirements as

when the port is enabled through POR

input2

(Reference clock is required)

2 If a SerDes port is enabled through the POR input and then disabled through DEVDISR, no hardware changes

are required. Termination of the SerDes port should follow what is required when the port is enabled through

both POR input and DEVDISR. See Note 1 for more information.

MPC8610EC датащи(PDF) 83 Page - Freescale Semiconductor, Inc

MPC8610EC датащи(HTML) 83 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

датащи скачать

ссылки URL