MPC8610EC datasheet(53/96 Pages) FREESCALE

53 / 96 page

Electrical Characteristics

MPC8610 Integrated Host Processor Hardware Specifications, Rev. 0

Freescale Semiconductor

2.16.2

PCI AC Electrical Specifications

This section describes the general AC timing parameters of the PCI bus. Note that the SYSCLK signal is used as the PCI input

clock. Table 46 provides the PCI AC timing specifications at 66 MHz.

Figure 15 provides the AC test load for PCI.

Figure 26. PCI AC Test Load

Table 46. PCI AC Timing Specifications at 66 MHz

Parameter

Symbol1

Min

Max

Unit

Notes

SYSCLK to output valid

tPCKHOV

1.5

7.4

2, 3, 12

SYSCLK to output high impedance

tPCKHOZ

—

2, 4, 11

Input setup to SYSCLK

tPCIVKH

3.7

—

2, 5, 10,

Input hold from SYSCLK

tPCIXKH

0.8

—

2, 5, 10,

REQ64 to HRESET 9 setup time

tPCRVRH

× tSYS

—

clocks

6, 7, 11

HRESET to REQ64 hold time

tPCRHRX

050

7, 11

HRESET high to first FRAME assertion

tPCRHFV

—

clocks

8, 11

Notes:

1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for

inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing

(PC) with respect to the time the input signals (I) reach the valid state (V) relative to the SYSCLK clock, tSYS, reference (K)

going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset (R)

went high (H) relative to the frame signal (F) going to the valid (V) state.

2. See the timing measurement conditions in the

PCI 2.3 Local Bus Specifications.

3. All PCI signals are measured from OVDD/2 of the rising edge of PCI_SYNC_IN to 0.4 × OVDD of the signal in question for

3.3-V PCI signaling levels.

4. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered

through the component pin is less than or equal to the leakage current specification.

5. Input timings are measured at the pin.

6. The timing parameter tSYS indicates the minimum and maximum CLK cycle times for the various specified frequencies. The

system clock period must be kept within the minimum and maximum defined ranges. For values see Section 3.1, “System

Clocking.”

7. The setup and hold time is with respect to the rising edge of HRESET.

8. The timing parameter tPCRHFV is a minimum of 10 clocks rather than the minimum of 5 clocks in the PCI 2.3 Local Bus

Specifications.

9. The reset assertion timing requirement for HRESET is 100

μs.

10.Guaranteed by characterization.

11.Guaranteed by design.

12. The timing parameter tPCKHOV is a minimum of 1.5 ns and a maximum of 7.4 ns rather than the minimum of 2 ns and a

maximum of 6 ns in the

PCI 2.3 Local Bus Specifications.

13. The timing parameter tPCIVKH is a minimum of 3.7 ns rather than the minimum of 3 ns in the PCI 2.3 Local Bus Specifications.

14. The timing parameter tPCIXKH is a minimum of 0.8 ns rather than the minimum of 0 ns in the PCI 2.3 Local Bus Specifications.

Output

Z0 = 50 Ω

OVDD/2

RL = 50 Ω

MPC8610EC датащи(PDF) 53 Page - Freescale Semiconductor, Inc

MPC8610EC датащи(HTML) 53 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

датащи скачать

ссылки URL