SC16C852LIB datasheet(31/60 Pages) PHILIPS

31 / 60 page

SC16C852L_2

Product data sheet

Rev. 02 — 25 January 2007

31 of 60

NXP Semiconductors

SC16C852L

1.8 V dual UART with 128-byte FIFOs and IrDA encoder/decoder

7.7 Line Status Register (LSR)

This register provides the status of data transfers between the SC16C852L and the CPU.

Table 22.

Line Status Register bits description

Bit

Symbol

Description

LSR[7]

FIFO data error.

logic 0 = no error (normal default condition)

logic 1 = at least one parity error, framing error or break indication is in the

current FIFO data. This bit is cleared when there are no remaining error ﬂags

associated with the remaining data in the FIFO.

LSR[6]

THR and TSR empty. This bit is the Transmit Empty indicator. This bit is set to a

logic 1 whenever the transmit holding register and the transmit shift register are

both empty. It is reset to logic 0 whenever either the THR or TSR contains a data

character. In the FIFO mode, this bit is set to ‘1’ whenever the transmit FIFO and

transmit shift register are both empty.

LSR[5]

THR empty. This bit is the Transmit Holding Register Empty indicator. This bit

indicates that the UART is ready to accept a new character for transmission. In

addition, this bit causes the UART to issue an interrupt to CPU when the THR

interrupt enable is set. The THR bit is set to a logic 1 when a character is

transferred from the transmit holding register into the transmitter shift register.

The bit is reset to a logic 0 concurrently with the loading of the transmitter

holding register by the CPU. In the FIFO mode, this bit is set when the transmit

FIFO is empty; it is cleared when at least 1 byte is written to the transmit FIFO.

LSR[4]

Break interrupt.

logic 0 = no break condition (normal default condition)

logic 1 = the receiver received a break signal (RX was a logic 0 for one

character frame time). In the FIFO mode, only one break character is loaded

into the FIFO.

LSR[3]

Framing error.

logic 0 = no framing error (normal default condition)

logic 1 = framing error. The receive character did not have a valid stop bit(s). In

the FIFO mode, this error is associated with the character at the top of the

FIFO.

LSR[2]

Parity error.

logic 0 = no parity error (normal default condition)

logic 1 = parity error. The receive character does not have correct parity

information and is suspect. In the FIFO mode, this error is associated with the

character at the top of the FIFO.

LSR[1]

Overrun error.

logic 0 = no overrun error (normal default condition)

logic 1 = overrun error. A data overrun error occurred in the Receive Shift

this case, the previous data in the shift register is overwritten. Note that under

this condition, the data byte in the Receive Shift Register is not transferred into

the FIFO, therefore the data in the FIFO is not corrupted by the error.

LSR[0]

Receive data ready.

logic 0 = no data in Receive Holding Register or FIFO (normal default

condition)

logic 1 = data has been received and is saved in the Receive Holding Register

or FIFO

SC16C852LIB датащи(PDF) 31 Page - NXP Semiconductors

SC16C852LIB датащи(HTML) 31 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

датащи скачать

ссылки URL