| поискавой системы для электроныых деталей |
|
MMPF0100Z датащи(PDF) 83 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MMPF0100Z датащи(HTML) 83 Page - NXP Semiconductors |
|
83 / 128 page ![]() NXP Semiconductors 83 PF0100Z FUNCTIONAL BLOCK REQUIREMENTS AND BEHAVIORS VGEN2 AC and transient PSRRVGEN2 PSRR (64) •IGEN2 = 187.5 mA, 20 Hz to 20 kHz VGEN2[3:0] = 0000 - 1101 VGEN2[3:0] = 1110, 1111 50 37 60 45 – – dB NOISEVGEN2 Output noise density •VIN1 = 1.75 V, IGEN2 = 187.5 mA 100 Hz – <1.0 kHz 1.0 kHz – <10 kHz 10 kHz – 1.0 MHz – – – -108 -118 -124 -100 -108 -112 dBV/ √Hz SLWRVGEN2 Turn-on slew rate • 10% to 90% of end value •1.75 V ≤ VIN1 ≤ 3.4 V, IGEN2 = 0.0 mA VGEN2[3:0] = 0000 to 0111 VGEN2[3:0] = 1000 to 1111 – – – – 12.5 16.5 mV /μs GEN2tON Turn-on time Enable to 90% of end value, VIN1 = 1.75 V, 3.4 V IGEN2 = 0.0 mA 60 – 500 μs GEN2tOFF Turn-off time Disable to 10% of initial value, VIN1 = 1.75 V IGEN2 = 0.0 mA –– 10 ms GEN2OSHT Start-up overshoot VIN1 = 1.75 V, 3.4 V, IGEN2 = 0.0 mA –1.0 2.0 % VGEN2LOTR Transient load response VIN1 = 1.75 V, 3.4 V IGEN2 = 25 mA to 250 mA in 1.0 μs Peak of overshoot or undershoot of VGEN2 with respect to final value Refer to Figure 25 –– 3.0 % VGEN2LITR Transient line response IGEN2 = 187.5 mA VIN1INITIAL = 1.75 V to VIN1FINAL = 2.25 V for VGEN2[3:0] = 0000 to 1101 VIN1INITIAL = VGEN2+0.3 V to VIN1FINAL = VGEN2+0.8 V for VGEN2[3:0] = 1110, 1111 Refer to Figure 25 –5.0 8.0 mV Notes 64. The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied separately from the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to operate in the dropout region of the regulator under test. Table 102. VGEN2 electrical characteristics (continued) All parameters are specified at PF0100Z TA = -40 °C to 85 °C, PF0100AZ TA = -40 °C to 105 °C, VIN = 3.6 V, VIN1 = 3.0 V, VGEN2[3:0] = 1111, IGEN2 = 10 mA, typical external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6V, VIN1 = 3.0 V, VGEN2[3:0] = 1111, IGEN2 = 10mA and 25°C, unless otherwise noted. Symbol Parameter Min. Typ. Max. Unit Notes |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |