 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
MMPF0100Z датащи(PDF) 33 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MMPF0100Z датащи(HTML) 33 Page - NXP Semiconductors |
|
|
33 / 128 page  NXP Semiconductors 33 PF0100Z FUNCTIONAL BLOCK REQUIREMENTS AND BEHAVIORS 6.4.4 Buck regulators Each buck regulator is capable of operating in PFM, APS, and PWM switching modes. 6.4.4.1 Current limit Each buck regulator has a programmable current limit. In an overcurrent condition, the current is limited cycle-by-cycle. If the current limit condition persists for more than 8.0 ms, a fault interrupt is generated. 6.4.4.2 General control To improve system efficiency the buck regulators can operate in different switching modes. Changing between switching modes can occur by any of the following means: I2C programming, exiting/entering the standby mode, exiting/entering sleep mode, and load current variation. Available switching modes for buck regulators are presented in Table 29. During soft-start of the buck regulators, the controller transitions through the PFM, APS, and PWM switching modes. 3.0 ms (typical) after the output voltage reaches regulation, the controller transitions to the selected switching mode. Depending on the particular switching mode selected, additional ripple may be observed on the output voltage rail as the controller transitions between switching modes. Contact your NXP representative for application considerations if you are using load switches in series with the buck regulator outputs. Table 30 summarizes the buck regulator programmability for normal and standby modes. Transitioning between normal and standby modes can affect a change in switching modes as well as output voltage. The rate of the output voltage change is controlled by the dynamic voltage scaling (DVS), explained in 6.4.4.2.1 Dynamic voltage scaling, page 34. For each regulator, the output voltage options are the same for normal and standby modes. Table 29. Switching mode description Mode Description OFF The regulator is switched off and the output voltage is discharged. PFM In this mode, the regulator is always in PFM mode, which is useful at light loads for optimized efficiency. PWM In this mode, the regulator is always in PWM mode operation regardless of load conditions. APS In this mode, the regulator moves automatically between pulse skipping mode and PWM mode depending on load conditions. Table 30. Regulator mode control SWxMODE[3:0] Normal mode Standby mode 0000 Off Off 0001 PWM Off 0010 Reserved Reserved 0011 PFM Off 0100 APS Off 0101 PWM PWM 0110 PWM APS 0111 Reserved Reserved 1000 APS APS 1001 Reserved Reserved 1010 Reserved Reserved 1011 Reserved Reserved 1100 APS PFM 1101 PWM PFM 1110 Reserved Reserved 1111 Reserved Reserved |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
