ADuC7023BCBZ62I-R7 datasheet(71/96 Pages) AD

71 / 96 page

Data Sheet

ADuC7023

| Page 71 of 96

PULSE-WIDTH MODULATOR

PULSE-WIDTH MODULATOR GENERAL OVERVIEW

The ADuC7023 integrates a 5-channel pulse-width modulator

(PWM) interface. The PWM outputs can be configured to drive

an H-bridge or can be used as standard PWM outputs. On

power-up, the PWM outputs default to H-bridge mode. This

ensures that the motor is turned off by default. In standard

PWM mode, the outputs are arranged as three pairs of PWM

pins. Users have control over the period of each pair of outputs

and over the duty cycle of each individual output.

Table 84. PWM MMRs

MMR Name

Description

PWMCON1

PWM Control Register 1.

PWM0COM0

Compare Register 0 for PWM Output 0 and

PWM Output 1.

PWM0COM1

Compare Register 1 for PWM Output 0 and

PWM Output 1.

PWM0COM2

Compare Register 2 for PWM Output 0 and

PWM Output 1.

PWM0LEN

Frequency control for PWM Output 0 and PWM

Output 1.

PWM1COM0

Compare Register 0 for PWM Output 2 and

PWM Output 3.

PWM1COM1

Compare Register 1 for PWM Output 2 and

PWM Output 3.

PWM1COM2

Compare Register 2 for PWM Output 2 and

PWM Output 3.

PWM1LEN

Frequency control for PWM Output 2 and PWM

Output 3.

PWM2COM0

Compare Register 0 for PWM Output 4

PWM2COM1

Compare Register 1 for PWM Output 4

PWMCLRI

PWM interrupt clear.

In all modes, the PWMxCOMx MMRs control the point at

which the PWM outputs change state. An example of the first

pair of PWM outputs (PWM0 and PWM1) is shown in Figure 40.

HIGH SIDE

(PWM0)

LOW SIDE

(PWM1)

PWM0COM2

PWM0COM1

PWM0COM0

PWM0LEN

Figure 40. PWM Timing

The PWM clock is selectable via PWMCON1 with one of the

following values: UCLK divided by 2, 4, 8, 16, 32, 64, 128, or

256. The length of a PWM period is defined by PWMxLEN.

The PWM waveforms are set by the count value of the 16-bit

timer and the compare registers contents, as shown with the

PWM0 and PWM1 waveforms in Figure 40.

The low-side waveform, PWM1, goes high when the timer

count reaches PWM0LEN, and it goes low when the timer

count reaches the value held in PWM0COM2 or when the

high-side waveform (PWM0) goes low.

The high-side waveform, PWM0, goes high when the timer

count reaches the value held in PWM0COM0, and it goes low

when the timer count reaches the value held in PWM0COM1.

PWMCON1 Control Register

Name:

PWMCON1

Address:

0xFFFF0F80

Default value:

0x0012

Access:

Read and write

Function:

This is a 16-bit MMR that configures the

PWM outputs.

Rev. E

ADuC7023BCBZ62I-R7 датащи(PDF) 71 Page - Analog Devices

ADuC7023BCBZ62I-R7 датащи(HTML) 71 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

датащи скачать

ссылки URL