ADuC7023BCBZ62I-R7 datasheet(46/96 Pages) AD

46 / 96 page

ADuC7023

Data Sheet

| Page 46 of 96

DACBKEY0 Register

Name:

DACBKEY0

Address:

0xFFFF0650

Default value:

0x0000

Access:

Write

DACBKEY1 Register

Name:

DACBKEY1

Address:

0xFFFF0658

Default value:

0x0000

Access:

Write

Table 44. DACBCFG Write Sequence

Name

Code

DACBKEY0

0x9A

DACBCFG

User value

DACBKEY1

0x0C

POWER SUPPLY MONITOR

The power supply monitor regulates the IOVDD supply on the

ADuC7023. It indicates when the IOVDD supply pin drops

below a supply trip point. The monitor function is controlled

via the PSMCON register. If enabled in the IRQEN or FIQEN

the PSMCON MMR. This bit is immediately cleared when

CMP goes high.

This monitor function allows the user to save working registers

to avoid possible data loss due to low supply or brownout

conditions. It also ensures that normal code execution does not

resume until a safe supply level has been established.

PSMCON Register

Name:

PSMCON

Address:

0xFFFF0440

Default value:

0x0008

Access:

Read/write

Table 45. PSMCON MMR Bit Descriptions

Bit

Name

Description

CMP

Comparator bit. This is a read-only bit that

directly reflects the state of the comparator.

Read 1 indicates the IOVDD supply is above its

selected trip point, or the PSM is in power-down

mode. Read 0 indicates the IOVDD supply is

below its selected trip point. This bit should be

set before leaving the interrupt service routine.

Trip point selection bits.

0 = 2.79 V.

1 = reserved.

PSMEN

Power supply monitor enable bit.

This bit is set to 1 to enable the power supply

monitor circuit.

This bit is cleared to 0 to disable the power

supply monitor circuit.

PSMI

Power supply monitor interrupt bit. This bit is set

high by the MicroConverter once CMP goes low,

indicating low I/O supply. The PSMI bit can be

used to interrupt the processor. Once CMP

returns high, the PSMI bit can be cleared by

writing a 1 to this location. A 0 write has no

effect. There is no timeout delay; PSMI can be

immediately cleared once CMP goes high.

COMPARATOR

The ADuC7023 integrates voltage comparators. The positive

input is multiplexed with ADC2, and the negative input has two

options: ADC3 or DAC0. The output of the comparator can be

configured to generate a system interrupt, be routed directly to

the programmable logic array, start an ADC conversion, or be

on an external pin, COMPOUT, as shown in Figure 34.

MUX

IRQ

MUX

DAC0

ADC2/CMP0

ADC3/CMP1

P0.5/COMPOUT

Figure 34. Comparator

Hysteresis

Figure 35 shows how the input offset voltage and hysteresis

terms are defined. Input offset voltage (VOS) is the difference

between the center of the hysteresis range and the ground level.

This can either be positive or negative. The hysteresis voltage

(VH) is ½ the width of the hysteresis range.

COMPOUT

CMP0

VOS

Figure 35. Comparator Hysteresis Transfer Function

Rev. E

ADuC7023BCBZ62I-R7 датащи(PDF) 46 Page - Analog Devices

ADuC7023BCBZ62I-R7 датащи(HTML) 46 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

датащи скачать

ссылки URL