LPC2917SLASH01 datasheet(31/86 Pages) NXP

31 / 86 page

LPC2917_19_01_2

Preliminary data sheet

Rev. 02 — 17 June 2009

31 of 86

NXP Semiconductors

LPC2917/01; LPC2919/01

ARM9 microcontroller with CAN and LIN

6.12.4 UARTs

The LPC2917/2919/01 contains two identical UARTs located at different peripheral base

addresses. The key features are:

• 16-byte receive and transmit FIFOs.

• Register locations conform to 550 industry standard.

• Receiver FIFO trigger points at 1 byte, 4 bytes, 8 bytes and 14 bytes.

• Built-in baud rate generator.

• Support for RS-485/9-bit mode allows both software address detection and automatic

address detection using 9-bit mode.

The UART is commonly used to implement a serial interface such as RS232. The

LPC2917/2919/01 contains two industry-standard 550 UARTs with 16-byte transmit and

receive FIFOs, but they can also be put into 450 mode without FIFOs.

6.12.4.1

Pin description

The UART pins are combined with other functions on the port pins of the

LPC2917/2919/01. Table 16 shows the UART pins (x runs from 0 to 1).

6.12.4.2

Clock description

The UART modules are clocked by two different clocks; CLK_SYS_PESS and

CLK_UARTx (x = 0-1), see Section 6.7.2. Note that each UART has its own CLK_UARTx

branch clock for power management. The frequency of all CLK_UARTx clocks is identical

since they are derived from the same base clock BASE_CLK_UART. The register

interface towards the system bus is clocked by CLK_SYS_PESS. The baud generator is

clocked by the CLK_UARTx.

6.12.5 Serial peripheral interface (SPI)

The LPC2917/2919/01 contains three Serial Peripheral Interface modules (SPIs) to allow

synchronous serial communication with slave or master peripherals.

The key features are:

• Master or slave operation

• Each SPI supports up to four slaves in sequential multi-slave operation

• Supports timer-triggered operation

• Programmable clock bit rate and prescale based on SPI source clock

(BASE_SPI_CLK), independent of system clock

• Separate transmit and receive FIFO memory buffers; 16 bits wide, 32 locations deep

• Programmable choice of interface operation: Motorola SPI or Texas Instruments

Synchronous Serial Interfaces

• Programmable data-frame size from 4 to 16 bits

Table 16.

UART pins

Symbol

Pin name

Direction

Description

UARTx TXD

TXDx

OUT

UART channel x transmit data output

UARTx RXD

RXDx

UART channel x receive data input

LPC2917/01 датащи(PDF) 31 Page - NXP Semiconductors

LPC2917/01 датащи(HTML) 31 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

датащи скачать

ссылки URL