MPC8560CPX667JC datasheet(36/108 Pages) NXP

36 / 108 page

MPC8560 Integrated Processor Hardware Specifications, Rev. 4.2

Freescale Semiconductor

Local Bus

Table 32 describes the general timing parameters of the local bus interface of the MPC8560 with the DLL

bypassed.

Local bus clock to output high impedance

for LAD/LDP

TSEC2_TXD[6:5] = 00

tLBKHOZ2

—

2.5

7, 9

TSEC2_TXD[6:5] = 11

(default)

3.8

Notes:

1.The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state)

for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local

bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this

case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with

respect to the output (O) going invalid (X) or output hold time.

2.All timings are in reference to LSYNC_IN for DLL enabled mode.

3.Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between

complementary signals at OVDD/2.

4.All signals are measured from OVDD/2 of the rising edge of LSYNC_IN for DLL enabled to 0.4 × OVDD of the signal in question

for 3.3-V signaling levels.

5.Input timings are measured at the pin.

6.The value of tLBOTOT is defined as the sum of 1/2 or 1 ccb_clk cycle as programmed by LBCR[AHD], and the number of local

bus buffer delays used as programmed at power-on reset with configuration pins TSEC2_TXD[6:5].

For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered

through the component pin is less than or equal to the leakage current specification.

8.Guaranteed by characterization.

9.Guaranteed by design.

Table 32. Local Bus General Timing Parameters—DLL Bypassed

Parameter

POR Configuration

Symbol 1

Min

Max

Unit

Notes

Local bus cycle time

—

tLBK

6.0

—

Internal launch/capture clock to LCLK delay

—

tLBKHKT

2.3

3.9

LCLK[n] skew to LCLK[m] or LSYNC_OUT

—

tLBKSKEW

—

150

3, 9

Input setup to local bus clock (except

LUPWAIT)

—tLBIVKH1

5.7

—

4, 5

LUPWAIT input setup to local bus clock

—

tLBIVKH2

5.6

—

4, 5

Input hold from local bus clock (except

LUPWAIT)

—tLBIXKH1

-1.8

—

4, 5

LUPWAIT input hold from local bus clock

—

tLBIXKH2

-1.3

—

4, 5

LALE output transition to LAD/LDP output

transition (LATCH hold time)

—tLBOTOT

1.5

—

Local bus clock to output valid (except

LAD/LDP and LALE)

TSEC2_TXD[6:5] = 00

tLBKLOV1

—-0.3

TSEC2_TXD[6:5] = 11

(default)

1.2

Table 31. Local Bus General Timing Parameters—DLL Enabled (continued)

Parameter

POR Configuration

Symbol 1

Min

Max

Unit

Notes

MPC8560CPX667JC датащи(PDF) 36 Page - NXP Semiconductors

MPC8560CPX667JC датащи(HTML) 36 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL