PIC18F23K22-ESLASHML datasheet(108/496 Pages) MICROCHIP

108 / 496 page

PIC18(L)F2X/4XK22

DS41412C-page 108

Preliminary

 2010 Microchip Technology Inc.

7.6

Operation During Code-Protect

Data EEPROM memory has its own code-protect bits in

Configuration Words. External read and write

operations are disabled if code protection is enabled.

The microcontroller itself can both read and write to the

internal data EEPROM, regardless of the state of the

code-protect Configuration bit. Refer to Section 24.0

“Special Features of the CPU” for additional

information.

7.7

Protection Against Spurious Write

There are conditions when the user may not want to

write to the data EEPROM memory. To protect against

spurious EEPROM writes, various mechanisms have

been implemented. On power-up, the WREN bit is

cleared. In addition, writes to the EEPROM are blocked

during the Power-up Timer period (TPWRT).

The write initiate sequence and the WREN bit together

help prevent an accidental write during brown-out,

power glitch or software malfunction.

7.8

Using the Data EEPROM

The data EEPROM is a high-endurance, byte

addressable array that has been optimized for the

storage of frequently changing information (e.g.,

program variables or other data that are updated often).

When variables in one section change frequently, while

variables in another section do not change, it is possible

to exceed the total number of write cycles to the

EEPROM without exceeding the total number of write

cycles to a single byte. Refer to the Data EEPROM

Memory parameters in Section 27.0 “Electrical

Characteristics” for write cycle limits. If this is the case,

then an array refresh must be performed. For this

reason, variables that change infrequently (such as

constants, IDs, calibration, etc.) should be stored in

Flash program memory.

A simple data EEPROM refresh routine is shown in

Example 7-3.

EXAMPLE 7-3:

DATA EEPROM REFRESH ROUTINE

Note:

If data EEPROM is only used to store

constants and/or data that changes rarely,

an array refresh is likely not required. See

specification.

CLRF

EEADR

; Start at address 0

BCF

EECON1, CFGS

; Set for memory

BCF

EECON1, EEPGD

; Set for Data EEPROM

BCF

INTCON, GIE

; Disable interrupts

BSF

EECON1, WREN

; Enable writes

Loop

; Loop to refresh array

BSF

EECON1, RD

; Read current address

MOVLW

55h

;

MOVWF

EECON2

; Write 55h

MOVLW

0AAh

;

MOVWF

EECON2

; Write 0AAh

BSF

EECON1, WR

; Set WR bit to begin write

BTFSC

EECON1, WR

; Wait for write to complete

BRA

$-2

INCFSZ

EEADR, F

; Increment address

BRA

LOOP

; Not zero, do it again

BCF

EECON1, WREN

; Disable writes

BSF

INTCON, GIE

; Enable interrupts

PIC18F23K22-E/ML датащи(PDF) 108 Page - Microchip Technology

PIC18F23K22-E/ML датащи(HTML) 108 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL