PIC18F23K22-ESLASHML datasheet(96/496 Pages) MICROCHIP

96 / 496 page

PIC18(L)F2X/4XK22

DS41412C-page 96

Preliminary

 2010 Microchip Technology Inc.

FIGURE 6-2:

TABLE WRITE OPERATION

6.2

Control Registers

Several control registers are used in conjunction with

the TBLRD and TBLWT instructions. These include the:

• EECON1 register

• EECON2 register

• TABLAT register

• TBLPTR registers

6.2.1

EECON1 AND EECON2 REGISTERS

The EECON1 register (Register 6-1) is the control

not a physical register; it is used exclusively in the

memory write and erase sequences. Reading

EECON2 will read all ‘0’s.

The EEPGD control bit determines if the access will be

a program or data EEPROM memory access. When

EEPGD is clear, any subsequent operations will

operate on the data EEPROM memory. When EEPGD

is set, any subsequent operations will operate on the

program memory.

The CFGS control bit determines if the access will be

to the Configuration/Calibration registers or to program

memory/data EEPROM memory. When CFGS is set,

subsequent operations will operate on Configuration

registers regardless of EEPGD (see Section 24.0

“Special Features of the CPU”). When CFGS is clear,

memory selection access is determined by EEPGD.

The FREE bit allows the program memory erase

operation. When FREE is set, an erase operation is

initiated on the next WR command. When FREE is

clear, only writes are enabled.

The WREN bit, when set, will allow a write operation.

The WREN bit is clear on power-up.

The WRERR bit is set by hardware when the WR bit is

set and cleared when the internal programming timer

expires and the write operation is complete.

The WR control bit initiates write operations. The WR

bit cannot be cleared, only set, by firmware. Then WR

bit is cleared by hardware at the completion of the write

operation.

Table Pointer(1)

Table Latch (8-bit)

TBLPTRH

TBLPTRL

TABLAT

Program Memory

(TBLPTR<MSBs>)

TBLPTRU

Instruction: TBLWT*

Note 1: During table writes the Table Pointer does not point directly to Program Memory. The LSBs of TBLPRTL

actually point to an address within the write block holding registers. The MSBs of the Table Pointer deter-

mine where the write block will eventually be written. The process for writing the holding registers to the

program memory array is discussed in Section 6.5 “Writing to Flash Program Memory”.

Holding Registers

Program Memory

Note:

During normal operation, the WRERR is

read as ‘1’. This can indicate that a write

operation was prematurely terminated by

a Reset, or a write operation was

attempted improperly.

Note:

The EEIF interrupt flag bit of the PIR2

The EEIF flag stays set until cleared by

firmware.

PIC18F23K22-E/ML датащи(PDF) 96 Page - Microchip Technology

PIC18F23K22-E/ML датащи(HTML) 96 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL