PIC18F23K22-ESLASHML datasheet(62/496 Pages) MICROCHIP

62 / 496 page

PIC18(L)F2X/4XK22

DS41412C-page 62

Preliminary

 2010 Microchip Technology Inc.

4.4

Brown-out Reset (BOR)

PIC18(L)F2X/4XK22 devices implement a BOR circuit

that provides the user with a number of configuration and

power-saving options. The BOR is controlled by the

BORV<1:0> and BOREN<1:0> bits of the CONFIG2L

Configuration register. There are a total of four BOR

configurations which are summarized in Table 4-1.

The BOR threshold is set by the BORV<1:0> bits. If

BOR is enabled (any values of BOREN<1:0>, except

‘00’), any drop of VDD below VBOR for greater than

TBOR will reset the device. A Reset may or may not

occur if VDD falls below VBOR for less than TBOR. The

chip will remain in Brown-out Reset until VDD rises

above VBOR.

If the Power-up Timer is enabled, it will be invoked after

VDD rises above VBOR; it then will keep the chip in

Reset for an additional time delay, TPWRT. If VDD drops

below VBOR while the Power-up Timer is running, the

chip will go back into a Brown-out Reset and the

Power-up Timer will be initialized. Once VDD rises

above VBOR, the Power-up Timer will execute the

additional time delay.

BOR

and

the

Power-on

Timer

(PWRT)

are

independently configured. Enabling BOR Reset does

not automatically enable the PWRT.

The BOR circuit has an output that feeds into the POR

circuit and rearms the POR within the operating range

of the BOR. This early rearming of the POR ensures

that the device will remain in Reset in the event that VDD

falls below the operating range of the BOR circuitry.

4.4.1

DETECTING BOR

When BOR is enabled, the BOR bit always resets to ‘0’

on any BOR or POR event. This makes it difficult to

determine if a BOR event has occurred just by reading

the state of BOR alone. A more reliable method is to

simultaneously check the state of both POR and BOR.

This assumes that the POR and BOR bits are reset to

‘1’ by software immediately after any POR event. If

BOR is ‘0’ while POR is ‘1’, it can be reliably assumed

that a BOR event has occurred.

4.4.2

SOFTWARE ENABLED BOR

When BOREN<1:0> = 01, the BOR can be enabled or

disabled by the user in software. This is done with the

SBOREN control bit of the RCON register. Setting

SBOREN enables the BOR to function as previously

described. Clearing SBOREN disables the BOR

entirely. The SBOREN bit operates only in this mode;

otherwise it is read as ‘0’.

Placing the BOR under software control gives the user

the additional flexibility of tailoring the application to the

environment without having to reprogram the device to

change BOR configuration. It also allows the user to

tailor device power consumption in software by

eliminating the incremental current that the BOR

consumes. While the BOR current is typically very small,

it may have some impact in low-power applications.

4.4.3

DISABLING BOR IN SLEEP MODE

When BOREN<1:0> = 10, the BOR remains under

hardware

control

and

operates

previously

described. Whenever the device enters Sleep mode,

however, the BOR is automatically disabled. When the

device returns to any other operating mode, BOR is

automatically re-enabled.

This mode allows for applications to recover from

brown-out situations, while actively executing code,

when the device requires BOR protection the most. At

the same time, it saves additional power in Sleep mode

by eliminating the small incremental BOR current.

4.4.4

MINIMUM BOR ENABLE TIME

Enabling the BOR also enables the Fixed Voltage

Reference (FVR) when no other peripheral requiring the

FVR is active. The BOR becomes active only after the

FVR stabilizes. Therefore, to ensure BOR protection,

the FVR settling time must be considered when

enabling the BOR in software or when the BOR is

automatically enabled after waking from Sleep. If the

BOR is disabled, in software or by reentering Sleep

before the FVR stabilizes, the BOR circuit will not sense

a BOR condition. The FVRST bit of the VREFCON0

Note:

Even when BOR is under software control,

the BOR Reset voltage level is still set by

the BORV<1:0> Configuration bits. It

cannot be changed by software.

PIC18F23K22-E/ML датащи(PDF) 62 Page - Microchip Technology

PIC18F23K22-E/ML датащи(HTML) 62 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL