7220 datasheet(33/303 Pages) RENESAS

33 / 303 page

2-6

FUNCTIONAL DESCRIPTION

2.1 Central processing unit

7220 Group User’s Manual

2.1.4 Program counter (PC)

The program counter is a 16-bit counter consists of PCH and PCL, both of which are 8-bit registers.

The program counter indicates the address of the program to be executed next.

The M37221M6-XXXSP/FP uses the stored program system. To start a new operation, transfer the instruction

and the data, from the memory to the CPU. Ordinary, the program counter is controlled to indicate the

memory address to be sent next. After each instruction is executed, the instruction required next is called

out and this cycle is repeated until finished.

Note: The program counter of the M37221M6-XXXSP/FP is controlled automatically; however, make sure

to avoid differences between program flow and the program counter contents when operating the

stack pointer or directly changing the program counter contents.

2.1.5 Processor status register (PS)

The processor status register is an 8-bit register. It consists of 5 flags, which indicate the state after

arithmetic operations related to the internal CPU, and 3 flags which determine operation.

The following explains each of these flags. Refer to “6.9 Machine instruction table” of this USER’S

MANUAL or “SERIES 740 <SOFTWARE> USER’S MANUAL” concerning the change of these flags.

(1)

Carry flag (C) ...................................................... Bit 0

This flag stores any carry or borrow from the ALU after an arithmetic operation and is also changed

by the Shift instruction or Rotate instruction.

This flag is set to “1” by using the SEC instruction and is cleared to “0” by using the CLC instruction.

(2)

Zero flag (Z) ........................................................ Bit 1

This flag is set to “1” when the result of an arithmetic operation or a data transfer is “0” and is cleared

to “0” by any other result.

This flag has no meaning in the decimal mode.

(3)

Interrupt disable flag (I) ................................... Bit 2

This flag disables interrupts. When this flag is “1,” all interrupts except the BRK interrupt and reset

are disabled. This flag immediately becomes “1” when an interrupt is received. This flag is set to “1”

by using the SEI instruction and is cleared to “0” by using the CLI instruction.

(4)

Decimal operation mode flag (D) ................... Bit 3

This flag determines whether addition and substruction are performed in binary or decimal notation.

Binary arithmetic is performed when this flag is “0” and decimal arithmetic is performed with treating

each word as a 2-digit decimal when this flag is “1.” Decimal adjust is performed automatically at this

time. This flag is set to “1” by using the SED instruction and is cleared to “0” by using the CLD

instruction. Only the ADC and SBC instructions are used for decimal arithmetic.

Since this flag directly affects calculations, always initialize it after a reset.

(5)

Break flag (B) ...................................................... Bit 4

This flag determines whether or not an interrupt occurred by using the BRK instruction. When a BRK

instruction interrupt occurs, the flag B is set to “1”; for all other interrupts the flag is set to “0” and

pushed to the stack.

For the M37221M6-XXXSP/FP, interrupt vectors by using the BRK instruction are independent of

other interrupts, and it is possible to determine the cause of interrupt by jumping to the vector

address inherent to each interrupt. Therefore, it is not specifically necessary to refer to this flag.

Note: The BRK instruction will be used for debugging.

7220 датащи(PDF) 33 Page - Renesas Technology Corp

7220 датащи(HTML) 33 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL