AD9927BBCZ datasheet(33/100 Pages) AD

33 / 100 page

AD9927

Rev. 0 | Page 33 of 100

Length

Description

VREPD_ODD

13b

Number of repetitions for the V-Pattern Group D for odd lines.

VREPB_EVEN

13b

Number of repetitions for the V-Pattern Group B for even lines.

VREPC_EVEN

13b

Number of repetitions for the V-Pattern Group C for even lines.

VREPD_EVEN

13b

Number of repetitions for the V-Pattern Group D for even lines.

FREEZE1

13b

Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL0_EVEN [12:0]

FREEZE2

13b

Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL1_EVEN [12:0]

FREEZE3

13b

Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL0_ODD [12:0]

FREEZE4

13b

Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL1_ODD [12:0]

RESUME1

13b

Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL0_EVEN [17:13]

RESUME 2

13b

Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL1_EVEN [17:13]

RESUME3

13b

Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL0_ODD [17:13]

RESUME4

13b

Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL1_ODD [17:13]

LASTREPLEN_A

13b

Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.

Should be programmed to a value equal to the VLENA register.

LASTREPLEN_B

13b

Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.

Should be programmed to a value equal to the VLENB register.

LASTREPLEN_C

13b

Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.

Should be programmed to a value equal to the VLENC register.

LASTREPLEN_D

13b

Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.

Should be programmed to a value equal to the VLEND register.

LASTTOG_A

13b

Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.

Note that the toggle position is common for all vertical signals.

LASTTOG_B

13b

Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.

Note that the toggle position is common for all vertical signals.

LASTTOG_C

13b

Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.

Note that the toggle position is common for all vertical signals.

LASTTOG_D

13b

Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.

Note that the toggle position is common for all vertical signals.

VSEQALT_EN

Special V-sequence alternation mode is enabled when this register is programmed high.

VALT_MAP

Enables the use of FREEZE/RESUME register locations to specify the VALTSEL0 and VALTSEL1 registers.

Must be enabled if VSEQALT mode is enabled.

VALTSEL0_EVEN

18b

Select lines for special V-sequence alternation mode for even lines. Used to concatenate VPAT Groups A/B/C/D

into unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.

VALTSEL1_EVEN

18b

Select lines for special V-sequence alternation mode for even lines. Used to concatenate VPAT Groups A/B/C/D

into unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.

VALTSEL0_ODD

18b

Select lines for special V-sequence alternation mode for odd lines. Used to concatenate VPAT Groups A/B/C/D

into unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.

VALTSEL1_ODD

18b

Select lines for special V-sequence alternation mode for odd lines. Used to concatenate VPAT Groups A/B/C/D

into unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.

SPC_PAT_EN

Enable special V-pattern to be inserted into one repetition of a VPATA series.

SPC_PAT_EN [0]: set to 1 to enable VPATB to be used as special pattern insertion.

SPC_PAT_EN [1]: set to 1 to enable VPATC to be used as special pattern insertion.

SPC_PAT_EN [2]: set to 1 to enable VPATD to be used as special pattern insertion.

AD9927BBCZ датащи(PDF) 33 Page - Analog Devices

AD9927BBCZ датащи(HTML) 33 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

датащи скачать

ссылки URL