PIC18F23K22-ESLASHML datasheet(211/496 Pages) MICROCHIP

211 / 496 page

 2010 Microchip Technology Inc.

Preliminary

DS41412C-page 211

PIC18(L)F2X/4XK22

FIGURE 15-4:

SPI MASTER AND MULTIPLE SLAVE CONNECTION

15.2.1

SPI MODE REGISTERS

The MSSPx module has five registers for SPI mode

operation. These are:

• MSSPx STATUS register (SSPxSTAT)

• MSSPx Control register 1 (SSPxCON1)

• MSSPx Control register 3 (SSPxCON3)

• MSSPx Data Buffer register (SSPxBUF)

• MSSPx Address register (SSPxADD)

• MSSPx Shift register (SSPxSR)

(Not directly accessible)

SSPxCON1 and SSPxSTAT are the control and

STATUS registers in SPI mode operation. The

SSPxCON1 register is readable and writable. The

lower 6 bits of the SSPxSTAT are read-only. The

upper two bits of the SSPxSTAT are read/write.

In one SPI Master mode, SSPxADD can be loaded

with a value used in the Baud Rate Generator. More

information on the Baud Rate Generator is available in

Section 15.7 “Baud Rate Generator”.

SSPxSR is the shift register used for shifting data in

and out. SSPxBUF provides indirect access to the

SSPxSR register. SSPxBUF is the buffer register to

which data bytes are written, and from which data

bytes are read.

In receive operations, SSPxSR and SSPxBUF

together create a buffered receiver. When SSPxSR

receives a complete byte, it is transferred to SSPxBUF

and the SSPxIF interrupt is set.

During transmission, the SSPxBUF is not buffered. A

write to SSPxBUF will write to both SSPxBUF and

SSPxSR.

15.2.2

SPI MODE OPERATION

When initializing the SPI, several options need to be

specified. This is done by programming the appropriate

control bits (SSPxCON1<5:0> and SSPxSTAT<7:6>).

These control bits allow the following to be specified:

• Master mode (SCKx is the clock output)

• Slave mode (SCKx is the clock input)

• Clock Polarity (Idle state of SCKx)

• Data Input Sample Phase (middle or end of data

output time)

• Clock Edge (output data on rising/falling edge of

SCKx)

• Clock Rate (Master mode only)

• Slave Select mode (Slave mode only)

To enable the serial port, SSPx Enable bit, SSPxEN of

the SSPxCON1 register, must be set. To reset or

reconfigure SPI mode, clear the SSPxEN bit, re-initial-

ize the SSPxCONx registers and then set the SSPxEN

bit. This configures the SDIx, SDOx, SCKx and SSx

pins as serial port pins. For the pins to behave as the

serial port function, some must have their data direction

bits (in the TRIS register) appropriately programmed as

follows:

• SDIx must have corresponding TRIS bit set

• SDOx must have corresponding TRIS bit cleared

• SCKx (Master mode) must have corresponding

TRIS bit cleared

• SCKx (Slave mode) must have corresponding

TRIS bit set

• SSx must have corresponding TRIS bit set

SPI Master

SCLK

SDOx

SDIx

General I/O

SCLK

SDIx

SDOx

SSx

SPI Slave

SCLK

SDIx

SDOx

SSx

SPI Slave

SCLK

SDIx

SDOx

SSx

SPI Slave

PIC18F23K22-E/ML датащи(PDF) 211 Page - Microchip Technology

PIC18F23K22-E/ML датащи(HTML) 211 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL