| поискавой системы для электроныых деталей |
|
M16C/1N датащи(PDF) 38 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M16C/1N датащи(HTML) 38 Page - Renesas Technology Corp |
|
38 / 238 page ![]() Rev.1.00 Oct 20, 2004 page 26 of 222 M16C/1N Group 6. Clock Generation Circuit REJ09B0007-0100Z b7 b6 b5 b4 b3 b2 b1 b0 Clock prescaler reset flag Symbol CPSRF Address 008F16 When reset 0XXXXXXX2 RW RW Function Bit name Bit symbol CPSR Nothing is assigned. In an attempt to write to these bits, write "0". The value, if read, turns out to be indeterminate. Clock prescaler reset flag 0 : No effect 1 : Prescaler is reset (When read, the value is "0") CM20 CM21 CM22 CM23 Main clock switch bit Oscillation stop detection interrupt enable bit Oscillation stop detection bit Clock monitor bit (Note 5) Reserved bit Set to "0" Note 1: In case of writing to this register, set bit 0 of the protect register (address 000A16) to "1". Note 2: Set to "0" before stopping the oscillation of the main clock (XIN-XOUT). (stop mode, low power dissipation mode, on-chip oscillation mode) An oscillation stop is detected if the oscillation of the main clock (XIN-XOUT) is stopped when the following two conditions are satisfied: (1) the oscillation stop detection function is valid and (2) CM21=1. Note 3: Valid when CM20=1. Note 4: CM22 bit switches to "1" automatically if an oscillation stop is detected when both CM20 bit and CM 21 bit are "1". CM22 bit cannot be cleared when CM23=1. Note 5: This bit is valid when both CM20 bit is "1". Use this bit for the purpose of confirming XIN operation for oscillation stop detection interrupt execution. b7 b6 b5 b4 b3 b2 b1 b0 0 00 0 0 : XIN oscillating normally 1 : XIN stopping abnormally 0 : Select XIN clock 1 : Select on-chip oscillator (Note 4) 0 : Disabled 1 : Enabled (Note 3) 0 : The function is invalid 1 : The function is valid (Note 2) Oscillation stop detection register (Note 1) Symbol CM2 Address 000C16 When reset 000001002 RW RW RW RW RO RW Function Bit name Bit symbol Figure 6.3 Oscillation stop detection register and clock prescaler reset flag Figure 6.4 fC32 block diagram 1/32 Reset Clock prescaler fC32 XCIN Clock prescaler reset flag (bit 7 at address 008F16) set to "1" |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |