ATtiny43U datasheet(32/182 Pages) ATMEL

32 / 182 page

8048B–AVR–03/09

ATtiny43U

Idle mode enables the MCU to wake up from external triggered interrupts as well as internal

ones like the Timer Overflow. If wake-up from the Analog Comparator interrupt is not required,

the Analog Comparator can be powered down by setting the ACD bit in the “ACSR – Analog

Comparator Control and Status Register” on page 113. This will reduce power consumption in

Idle mode. If the ADC is enabled, a conversion starts automatically when this mode is entered.

7.1.2

ADC Noise Reduction Mode

When the SM1..0 bits are written to 01, the SLEEP instruction makes the MCU enter ADC Noise

Reduction mode, stopping the CPU but allowing the ADC, the external interrupts, and the

Watchdog to continue operating (if enabled). This sleep mode halts clk

I/O, clkCPU, and clkFLASH,

while allowing the other clocks to run.

This improves the noise environment for the ADC, enabling higher resolution measurements. If

the ADC is enabled, a conversion starts automatically when this mode is entered. Apart form the

ADC Conversion Complete interrupt, only an External Reset, a Watchdog Reset, a Brown-out

Reset, an SPM/EEPROM ready interrupt, an external level interrupt on INT0 or a pin change

interrupt can wake up the MCU from ADC Noise Reduction mode.

7.1.3

Power-Down Mode

When the SM1..0 bits are written to 10, the SLEEP instruction makes the MCU enter Power-

down mode. In this mode, the Oscillator is stopped, while the external interrupts, and the Watch-

dog continue operating (if enabled). Only an External Reset, a Watchdog Reset, a Brown-out

Reset, an external level interrupt on INT0, or a pin change interrupt can wake up the MCU. This

sleep mode halts all generated clocks, allowing operation of asynchronous modules only.

7.2

Software BOD Disable

When the Brown-out Detector (BOD) is enabled by BODLEVEL fuses (see Table 19.2 on page

140), the BOD is actively monitoring the power supply voltage during a sleep period. To save

power, it is possible for software to disable the BOD in Power-Down Mode (see “Power-Down

Mode” on page 32). The sleep mode power consumption will then be at the same level as when

BOD is globally disabled by fuses. If disabled by software, the BOD is turned off immediately

after entering the sleep mode and automatically turned on upon wake-up. This ensures safe

operation in case the V

CC level has dropped during the sleep period.

When the BOD has been disabled the wake-up time from sleep mode will be the same as the

wake-up time from RESET. This is in order to ensure the BOD is working correctly before the

MCU continues executing code.

BOD disable is controlled by bit 7 (BODS — BOD Sleep) of MCU Control Register, see “MCUCR

– MCU Control Register” on page 34. Writing this bit to one turns off the BOD in Power-Down

Mode, while a zero in this bit keeps BOD active. The default setting is zero, i.e. BOD active.

Writing to the BODS bit is controlled by a timed sequence and an enable bit, see “MCUCR –

MCU Control Register” on page 34.

7.3

Power Reduction Register

The Power Reduction Register (PRR), see “PRR – Power Reduction Register” on page 35, pro-

vides a method to stop the clock to individual peripherals to reduce power consumption. The

current state of the peripheral is frozenand the I/O registers can not be read or written.

Resources used by the peripheral when stopping the clock will remain occupied, hence the

ATtiny43U датащи(PDF) 32 Page - ATMEL Corporation

ATtiny43U датащи(HTML) 32 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL