LPC2921 datasheet(35/83 Pages) NXP

35 / 83 page

LPC2921_23_25_1

Preliminary data sheet

Rev. 01 — 15 June 2009

35 of 83

NXP Semiconductors

LPC2921/2923/2925

ARM9 microcontroller with CAN, LIN, and USB

A mechanism is provided to modify conﬁguration of the ADC and control the moment at

which the updated conﬁguration is transferred to the ADC domain.

The ADC clock is limited to 4.5 MHz maximum frequency and should always be lower than

or equal to the system clock frequency. To meet this constraint or to select the desired

lower sampling frequency, the clock generation unit provides a programmable fractional

system-clock divider dedicated to the ADC clock. Conversion rate is determined by the

ADC clock frequency divided by the number of resolution bits plus one. Accessing ADC

registers requires an enabled ADC clock, which is controllable via the clock generation

unit, see Section 6.15.2.

Each ADC has four start inputs. Note that start 0 and start 2 are captured in the system

clock domain while start 1 and start 3 are captured in the ADC domain. The start inputs

are connected at MSCSS level, see Section 6.14 for details.

6.14.4.2

Pin description

The two ADC modules in the MSCSS have the pins described below. The ADCx input pins

are combined with other functions on the port pins of the LPC2921/2923/2925. The

VREFN and VREFP pins are common for both ADCs. Table 20 shows the ADC pins.

Remark: Note that the ADC1 and ADC2 accept an input voltage up to of 3.6 V (see

Table 31) on the ADC1/2 IN pins. If the ADC is not used, the pins are 5 V tolerant.

Fig 6.

ADC block diagram

002aad960

ADC

start 2

ADC

start 0

APB clock

(BASE_MSCSS_CLK)

ADC clock

(up to 4.5 MHz)

(BASE_ADC_CLK)

APB system bus

IRQ scan

IRQ compare

ADC2 IN[7:0]

ADC

start 1

ADC

start 3

sync_out

ADC DOMAIN

SYSTEM DOMAIN

ADC

CONTROL

ADC

REGISTERS

3.3 V

ADC2

3.3 V

ADC1

ANALOG

MUX

conversion data

update

configuration data

IRQ

ADC1 IN[7:0]

ANALOG

MUX

3.3 V IN

Table 20.

Analog to digital converter pins

Symbol

Pin name

Direction

Description

ADC1/2 IN[7:0]

IN1/2[7:0]

analog input for 3.3 V ADC1/2, channel 7 to

channel 0

ADC2_EXT_START CAP1[2]

ADC external start-trigger input

VREFN

ADC LOW reference level

VREFP

ADC HIGH reference level

VDDA(ADC3V3)

VDDA(ADC3V3) IN

ADC1 and ADC2 3.3 V supply

LPC2921 датащи(PDF) 35 Page - NXP Semiconductors

LPC2921 датащи(HTML) 35 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83

датащи скачать

ссылки URL