MNSC140CORE datasheet(6/88 Pages) FREESCALE

6 / 88 page

MSC8122 Technical Data, Rev. 13

Freescale Semiconductor

Features

Ethernet Controller

• Designed to comply with IEEE® Std 802® including Std. 802.3™, 802.3u™, 802.3x™, and 802.3ac™.

• Three Ethernet physical interfaces:

— 10/100 Mbps MII.

— 10/100 Mbps RMII.

— 10/100 Mbps SMII.

• Full and half-duplex support.

• Full-duplex flow control (automatic PAUSE frame generation or software programmed PAUSE frame generation

and recognition).

• Out-of-sequence transmit queue for initiating flow-control.

• Programmable maximum frame length supports jumbo frames (up to 9.6k) and virtual local area network (VLAN)

tags and priority.

• Retransmission from transmit FIFO following a collision.

• CRC generation and verification of inbound/outbound packets.

• Address recognition:

— Each exact match can be programmed to be accepted or rejected.

— Broadcast address (accept/reject).

— Exact match 48-bit individual (unicast) address.

— Hash (256-bit hash) check of individual (unicast) addresses.

— Hash (256-bit hash) check of group (multicast) addresses.

— Promiscuous mode.

• Pattern matching:

— Up to 16 unique 4-byte patterns.

— Pattern match on bit-basis.

— Matching range up to 256 bytes deep into the frame.

— Offsets to a maximum of 252 bytes.

— Programmable pattern size in 4-byte increments up to 64 bytes.

— Accept or reject frames if a match is detected.

— Up to eight unicast addresses for exact matches.

— Pattern matching accepts/rejects IP addresses.

• Filing of receive frames based on pattern match; prioritization of frames.

• Insertion with expansion or replacement for transmit frames; VLAN tag insertion.

• RMON statistics.

• Master DMA on the local bus for fetching descriptors and accessing the buffers.

• Ethernet PHY can be exposed either on GPIO pins or on the high most significant bits of the DSI/system when

the DSI and the system bus are both 32 bits.

• MPC8260 8-byte width buffer descriptor mode as well as 32 byte width buffer descriptor mode.

• MII Bridge (MIIGSK):

— Programmable selection of the 50 MHz RMII reference clock source (external or internal).

— Independent 2 bit wide transmit and receive data paths.

— Six operating modes.

— Four general-purpose control signals.

— Programmable transmitted inter-frame bits to support inter-frame gap for frames in the SMII domain.

• SMII features:

— Multiplexed only with GPIO signals

— Convey complete MII information between the PHY and MAC.

— Allow direct MAC-to-MAC communication in SMII mode.

— Can generate an interrupt request line while receiving inter-frame segments.

Feature

Description

MNSC140CORE датащи(PDF) 6 Page - Freescale Semiconductor, Inc

MNSC140CORE датащи(HTML) 6 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

датащи скачать

ссылки URL