ADBMS2950BCCSZ datasheet(56/97 Pages) AD

56 / 97 page

ADBMS2950B

Data Sheet

Rev. 0 | Page 56 of 97

Note:

The thermal shutdown indicator bit THSD is not cleared by

the SRST command, but only after a power-on-reset or through

the CLRFLAG command.

Registers and bits that are subject to the SNAP, UNSNAP

protocol are marked with FRZ in the Type column of the

of the snap, unsnap commands, see the Snapshot Commands

section.

Both the non-volatile memories: NVM1 and NVM2 are

protected through ECC bits. Faults are reported into the SED1,

MED1, SED2, and MED2 bits. After power-up or reset, the

non-volatile memories are read and stored into volatile registers

that are implemented redundantly.

The STAT register contains status bits of read-only type. It can

be read with the RDSTAT command.

Table 75. STAT Register Map

BYTE

BIT 7

BIT 6

BIT 5

BIT 4

BIT 3

BIT 2

BIT 1

BIT 0

000000

OCBP

OCAP

I2CAL

I1CAL

0000

DER[1:0]

00000000

GPO6H

GPO5H

GPO4H

GPO3H

GPO2H

GPO1H

GPO6L

GPO5L

GPO4L

GPO3L

GPO2L

GPO1L

GPIO4L

GPIO3L

GPIO2L

GPIO1L

REVID[3:0]

0000

The RDSID command is used to read the SID register.

Table 76. SID Register Map

BYTE

BIT 7

BIT 6

BIT 5

BIT 4

BIT 3

BIT 2

BIT 1

BIT 0

SID[7:0]

SID[15:8]

SID[23:16]

SID[31:24]

SID[39:32]

SID[47]

DEVID[5:0]/SID[46:41]

SID[40]

Table 77. SID and STAT Bit Description

Name

Type

Reset

Value

Description

SID

As per part

48-bit Unique Serial Identifier. The DEVID uses 6 bits of the SID.

DEVID

As per derivative

Device Derivative Identifier is part of the serial identifier SDI[46:41].

00 0110

ADBMS2950B.

REVID

As per revision

Device Revision Identifier.

0001

Rev B.

0010

Rev C.

0011

Rev D.

0100

Rev E.

DER

As per derivative

Derivative Code.

ADBMS2950B.

Invalid.

OCAP

OCA Pin State, when OCMODE = 11 or for Diagnostics.

OCA pin reads back as low.

OCA pin reads back as high.

OCBP

OCB Pin State, when OCMODE = 11 or for Diagnostics.

OCB pin reads back as low.

OCB pin reads back as high.

I1CAL

I1ADC Initialization Status.

I1ADC has not yet completed initialization.

I1ADC has completed initialization.

I2CAL

I2ADC Initialization Status.

I2ADC has not yet completed initialization.

I2ADC has completed initialization.

GPIO1L

GPIO1 Read Back.

ADBMS2950BCCSZ датащи(PDF) 56 Page - Analog Devices

ADBMS2950BCCSZ датащи(HTML) 56 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97

датащи скачать

ссылки URL