 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
WM8912 датащи(PDF) 108 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
WM8912 датащи(HTML) 108 Page - Cirrus Logic |
|
|
108 / 129 page  WM8912 Production Data w PD, Rev 4.1, February 2013 108 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R67 (43h) DC Servo 0 3 DCS_ENA_CH AN_3 0 DC Servo enable for LINEOUTR 0 = disabled 1 = enabled 2 DCS_ENA_CH AN_2 0 DC Servo enable for LINEOUTL 0 = disabled 1 = enabled 1 DCS_ENA_CH AN_1 0 DC Servo enable for HPOUTR 0 = disabled 1 = enabled 0 DCS_ENA_CH AN_0 0 DC Servo enable for HPOUTL 0 = disabled 1 = enabled Register 43h DC Servo 0 REGISTER ADDRESS BIT LABEL DEFAULT DESCRIPTION REFER TO R68 (44h) DC Servo 1 15 DCS_TRIG_SI NGLE_3 0 Writing 1 to this bit selects a single DC offset correction for LINEOUTR. In readback, a value of 1 indicates that the DC Servo single correction is in progress. 14 DCS_TRIG_SI NGLE_2 0 Writing 1 to this bit selects a single DC offset correction for LINEOUTL. In readback, a value of 1 indicates that the DC Servo single correction is in progress. 13 DCS_TRIG_SI NGLE_1 0 Writing 1 to this bit selects a single DC offset correction for HPOUTR. In readback, a value of 1 indicates that the DC Servo single correction is in progress. 12 DCS_TRIG_SI NGLE_0 0 Writing 1 to this bit selects a single DC offset correction for HPOUTL. In readback, a value of 1 indicates that the DC Servo single correction is in progress. 11 DCS_TRIG_SE RIES_3 0 Writing 1 to this bit selects a series of DC offset corrections for LINEOUTR. In readback, a value of 1 indicates that the DC Servo DAC Write correction is in progress. 10 DCS_TRIG_SE RIES_2 0 Writing 1 to this bit selects a series of DC offset corrections for LINEOUTL. In readback, a value of 1 indicates that the DC Servo DAC Write correction is in progress. 9 DCS_TRIG_SE RIES_1 0 Writing 1 to this bit selects a series of DC offset corrections for HPOUTR. In readback, a value of 1 indicates that the DC Servo DAC Write correction is in progress. 8 DCS_TRIG_SE RIES_0 0 Writing 1 to this bit selects a series of DC offset corrections for HPOUTL. In readback, a value of 1 indicates that the DC Servo DAC Write correction is in progress. 7 DCS_TRIG_ST ARTUP_3 0 Writing 1 to this bit selects Start-Up DC Servo mode for LINEOUTR. In readback, a value of 1 indicates that the DC Servo Start-Up correction is in progress. 6 DCS_TRIG_ST ARTUP_2 0 Writing 1 to this bit selects Start-Up DC Servo mode for LINEOUTL. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
