PIC17C752-08SLASHCL datasheet(91/328 Pages) MICROCHIP

91 / 328 page

DS30289A-page 91

PIC17C7XX

10.10

I/O Programming Considerations

10.10.1 BI-DIRECTIONAL I/O PORTS

Any instruction which writes, operates internally as a

read followed by a write operation. For example, the

BCF

and BSF instructions read the register into the

CPU, execute the bit operation, and write the result

back to the register. Caution must be used when these

instructions are applied to a port with both inputs and

outputs deﬁned. For example, a BSF operation on bit5

of PORTB will cause all eight bits of PORTB to be read

into the CPU. Then the BSF operation takes place on

bit5 and PORTB is written to the output latches. If

another bit of PORTB is used as a bi-directional I/O pin

(e.g. bit0) and it is deﬁned as an input at this time, the

input signal present on the pin itself would be read into

the CPU and re-written to the data latch of this particu-

lar pin, overwriting the previous content. As long as the

pin stays in the input mode, no problem occurs. How-

ever, if bit0 is switched into output mode later on, the

content of the data latch may now be unknown.

Reading a port reads the values of the port pins. Writ-

ing to the port register writes the value to the port latch.

When using read-modify-write instructions (BCF, BSF,

BTG

, etc.) on a port, the value of the port pins is read,

the desired operation is performed with this value, and

the value is then written to the port latch.

Example 10-1 shows the possible effect of two sequen-

tial read-modify-write instructions on an I/O port.

EXAMPLE 10-1: READ MODIFY WRITE

INSTRUCTIONS ON AN

I/O PORT

; Initial PORT settings: PORTB<7:4> Inputs

;

PORTB<3:0> Outputs

; PORTB<7:6> have pull-ups and are

; not connected to other circuitry

;

PORT latch

PORT pins

;

----------

---------

;

BCF

PORTB, 7

; 01pp pppp

11pp pppp

BCF

PORTB, 6

; 10pp pppp

11pp pppp

BCF

DDRB, 7

; 10pp pppp

11pp pppp

BCF

DDRB, 6

; 10pp pppp

10pp pppp

;

; Note that the user may have expected the

; pin values to be 00pp pppp. The 2nd BCF

; caused RB7 to be latched as the pin value

; (High).

Note:

A pin actively outputting a Low or High

should not be driven from external devices

in order to change the level on this pin (i.e.

“wired-or”, “wired-and”). The resulting high

output currents may damage the device.

PIC17C752-08/CL датащи(PDF) 91 Page - Microchip Technology

PIC17C752-08/CL датащи(HTML) 91 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL