PIC16C925-SSLASHCL datasheet(83/182 Pages) MICROCHIP

83 / 182 page

 2001 Microchip Technology Inc.

Preliminary

DS39544A-page 81

PIC16C925/926

FIGURE 10-4:

A/D RESULT JUSTIFICATION

10.5

A/D Operation During SLEEP

The A/D module can operate during SLEEP mode. This

requires that the A/D clock source be set to RC

(ADCS<1:0> = 11). When the RC clock source is

selected, the A/D module waits one instruction cycle

before starting the conversion. This allows the SLEEP

instruction to be executed, which eliminates all digital

switching noise from the conversion. When the conver-

sion is completed, the GO/DONE bit will be cleared and

the result loaded into the ADRES register. If the A/D

interrupt is enabled, the device will wake-up from

SLEEP. If the A/D interrupt is not enabled, the A/D mod-

ule will then be turned off, although the ADON bit will

remain set.

When the A/D clock source is another clock option (not

RC), a SLEEP instruction will cause the present conver-

sion to be aborted and the A/D module to be turned off,

though the ADON bit will remain set.

Turning off the A/D places the A/D module in its lowest

current consumption state.

10.6

Effects of a RESET

A device RESET forces all registers to their RESET

state. This forces the A/D module to be turned off, and

any conversion is aborted. All A/D input pins are con-

figured as analog inputs.

The value that is in the ADRESH:ADRESL registers is

not

modified

for

Power-on

Reset.

The

ADRESH:ADRESL registers will contain unknown data

after a Power-on Reset.

TABLE 10-2:

REGISTERS/BITS ASSOCIATED WITH A/D

10-Bit Result

ADRESH

ADRESL

0000 00

ADFM = 0

2 1 0 7

10-bit Result

ADRESH

ADRESL

10-bit Result

0000 00

0 7 6 5

ADFM = 1

Right Justified

Left Justified

Note:

For the A/D module to operate in SLEEP,

the A/D clock source must be set to RC

(ADCS<1:0> = 11). To allow the conver-

sion to occur during SLEEP, ensure the

SLEEP

instruction immediately follows the

instruction that sets the GO/DONE bit.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

POR,

BOR

MCLR,

WDT

0Bh

INTCON

GIE

PEIE

TMR0IE

INTE

RBIE

TMR0IF

INTF

RBIF

0000 000x

0000 000u

0Ch

PIR1

LCDIF

ADIF

(1)

SSPIF

CCP1IF

TMR2IF TMR1IF

r0rr 0000

8Ch

PIE1

LCDIE

ADIE

(1)

SSPIE

CCP1IE

TMR2IE TMR1IE

r0rr 0000

1Eh

ADRESH

A/D Result Register High Byte

xxxx xxxx

uuuu uuuu

9Eh

ADRESL

A/D Result Register Low Byte

xxxx xxxx

uuuu uuuu

1Fh

ADCON0

ADCS1

ADCS0

CHS2

CHS1

CHS0

GO/DONE

—

ADON

0000 00-0

9Fh

ADCON1

ADFM

—

PCFG3

PCFG2

PCFG1

PCFG0

--0- 0000

85h

TRISA

—

PORTA Data Direction Register

--11 1111

05h

PORTA

—

PORTA Data Latch when written: PORTA pins when read

--0x 0000

--0u 0000

Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used for A/D conversion.

Note 1: These bits are reserved; always maintain these bits clear.

PIC16C925-S/CL датащи(PDF) 83 Page - Microchip Technology

PIC16C925-S/CL датащи(HTML) 83 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL