| поискавой системы для электроныых деталей |
|
PIC16C925-S/CL датащи(PDF) 55 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16C925-S/CL датащи(HTML) 55 Page - Microchip Technology |
|
55 / 182 page ![]() 2001 Microchip Technology Inc. Preliminary DS39544A-page 53 PIC16C925/926 8.0 CAPTURE/COMPARE/PWM (CCP) MODULE The CCP (Capture/Compare/PWM) module contains a 16-bit register which can operate as a 16-bit capture register, as a 16-bit compare register, or as a PWM master/slave duty cycle register. Table 8-1 shows the timer resources used by the CCP module. The Capture/Compare/PWM Register1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). The CCP1CON register con- trols the operation of CCP1. All three are readable and writable. Register 8-1 shows the CCP1CON register. For use of the CCP module, refer to the Embedded Control Handbook, “Using the CCP Modules” (AN594). TABLE 8-1: CCP MODE - TIMER RESOURCE REGISTER 8-1: CCP1CON REGISTER (ADDRESS 17h) CCP Mode Timer Resource Capture Compare PWM Timer1 Timer1 Timer2 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0 bit 7 bit 0 bit 7-6 Unimplemented: Read as '0' bit 5-4 CCP1X:CCP1Y: PWM Least Significant bits Capture mode: Unused Compare mode: Unused PWM mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L. bit 3-0 CCP1M3:CCP1M0: CCP1 Mode Select bits 0000 = Capture/Compare/PWM disabled (resets CCP1 module) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set output on match (bit CCP1IF is set) 1001 = Compare mode, clear output on match (bit CCP1IF is set) 1010 = Compare mode, generate software interrupt-on-match (bit CCP1IF is set, CCP1 pin is unaffected) 1011 = Compare mode, trigger special event (CCP1IF bit is set; CCP1 resets TMR1) 11xx = PWM mode Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR ’1’ = Bit is set ’0’ = Bit is cleared x = Bit is unknown |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |