| поискавой системы для электроныых деталей |
|
TMP93CS41 датащи(PDF) 20 Page - Toshiba Semiconductor |
|
|
|||||||||||||||||||||||||||||
TMP93CS41 датащи(HTML) 20 Page - Toshiba Semiconductor |
|
20 / 248 page ![]() TMP93CS40/TMP93CS41 2004-02-10 93CS40-18 3.3.1 System Clock Controller The system clock controller generates the system clock signal (fSYS) for the CPU core and internal I/O. It contains two oscillation circuits and a clock gear circuit for high frequency (fc). The register SYSCR1<SYSCK> changes the system clock to either fc or fs, SYSCR0<XEN> and SYSCR0<XTEN> control enabling and disabling each oscillator, and SYSCR1<GEAR2:0> changes the high-frequency clock gear to either 1, 2, 4, 8, or 16 (fc, fc/2, fc/4, fc/8, or fc/16). These functions can reduce the power consumption of the equipment in which the device is installed. The system clock (fSYS) is set to fc/32 (fc/16 × 1/2) by the setting of <XEN> = 1, <XTEN> = 0, <SYSCK> = 0, and <GEAR2:0> = 100 upon resetting. For example, fSYS is set to 0.625 MHz by resetting in the case where the 20 MHz oscillator is connected to the X1 and X2 pins. The high frequency (fc) and low frequency (fs) clock signals can be easily obtained by connecting a resonator to the X1 and X2, XT1 and XT2 pins, respectively. Clock input from an external oscillator is also possible. The XT1 and XT2 pins can also function as ports 96 and 97. Therefore in the case of single clock mode, the XT1 and XT2 pins can be used as I/O port pins. Figure 3.3.4 Examples of Resonator Connection Note 1: Note on using the low-frequency oscillation circuit. In connecting the low-frequency resonator to ports 96 and 97, it is necessary to make the following settings to reduce the power consumption. (Connecting with resonators) P9CR<P96C, P97C> = 11, P9<P96:97> = 00 (Connecting with oscillators) P9CR<P96C, P97C> = 11, P9<P96:97> = 10 Note 2: Accurate adjustment of the oscillation frequency The CLK pin output at 1/2 the system clock frequency (fSYS/2) is used to monitor the oscillation clock. With a system requiring adjustment of the oscillation frequency, an adjusting program must be written. Low-frequency clock High-frequency clock (b) External oscillator (a) Crystal/ceramic resonator (b) External oscillator (c) Crystal resonator X1 X2 74HCU04 * See application circuit in chapter 5. X1 X2 XT1 XT2 XT1 XT2 (Open) |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |