AM62A7 datasheet(157/238 Pages) TI1

157 / 238 page

7.10.5.12 I2C

The device contains six multicontroller Inter-Integrated Circuit (I2C) controllers. Each I2C controller was

designed to be compliant to the Philips I2C-bus™ specification version 2.1. However, the device IOs are not

fully compliant to the I2C electrical specification. The speeds supported and exceptions are described per port

below:

• I2C0, I2C1, I2C2, and I2C3

– Speeds:

• Standard-mode (up to 100 Kbits/s)

– 1.8 V

– 3.3 V

• Fast-mode (up to 400 Kbits/s)

– 1.8 V

– 3.3 V

– Exceptions:

• The IOs associated with these ports are not compliant to the fall time requirements defined in the I2C

specification because they are implemented with higher performance LVCMOS push-pull IOs that were

designed to support other signal functions that could not be implemented with I2C compatible IOs. The

LVCMOS IOs being used on these ports are connected such they emulate open-drain outputs. This

emulation is achieved by forcing a constant low output and disabling the output buffer to enter the Hi-Z

state.

• The I2C specification defines a maximum input voltage VIH of (VDD

max + 0.5 V), which exceeds the

absolute maximum ratings for the device IOs. The system must be designed to ensure the I2C signals

never exceed the limits defined in the Absolute Maximum Ratings section of this datasheet.

• MCU_I2C0 and WKUP_I2C0

– Speeds:

• Standard-mode (up to 100 Kbits/s)

– 1.8 V

– 3.3 V

• Fast-mode (up to 400 Kbits/s)

– 1.8 V

– 3.3 V

• Hs-mode (up to 3.4 Mbits/s)

– 1.8 V

– Exceptions:

• The IOs associated with these ports were not design to support Hs-mode while operating at 3.3 V. So

Hs-mode is limited to 1.8-V operation.

• The rise and fall times of the I2C signals connected to these ports must not exceed a slew rate of 0.8

V/ns (or 8E+7 V/s). This limit is more restrictive than the minimum fall time limits defined in the I2C

specification. Therefore, it may be necessary to add additional capacitance to the I2C signals to slow

the rise and fall times such that they do not exceed a slew rate of 0.8 V/ns.

• The I2C specification defines a maximum input voltage VIH of (VDD

max + 0.5 V), which exceeds the

absolute maximum ratings for the device IOs. The system must be designed to ensure the I2C signals

never exceed the limits defined in the Absolute Maximum Ratings section of this datasheet.

Note

I2C3 has one or more signals which can be multiplexed to more than one pin. Timing is only valid for

specific pin combinations known as IOSETs. Valid pin combinations or IOSETs for this interface are

defined in the SysConfig-PinMux Tool.

Refer to the Philips I2C-bus specification version 2.1 for timing details.

For more details about features and additional description information on the device Inter-Integrated Circuit, see

the corresponding subsections within Signal Descriptions and Detailed Description sections.

www.ti.com

AM62A7, AM62A7-Q1, AM62A3, AM62A3-Q1

SPRSP77A – MARCH 2023 – REVISED AUGUST 2023

Submit Document Feedback

157

Product Folder Links: AM62A7 AM62A7-Q1 AM62A3 AM62A3-Q1

AM62A7 датащи(PDF) 157 Page - Texas Instruments

AM62A7 датащи(HTML) 157 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL