AM62A7 datasheet(84/238 Pages) TI1

84 / 238 page

7.7 Electrical Characteristics

Note

The interfaces or signals described in Section 7.7 correspond to the interfaces or signals available in

multiplexing mode 0 (Primary Signal Function).

All interfaces or signals multiplexed on the balls described in these tables have the same DC electrical

characteristics, unless multiplexing involves a PHY and GPIO combination, in which case different DC

electrical characteristics are specified for the different multiplexing modes (Functions).

7.7.1 I2C Open-Drain, and Fail-Safe (I2C OD FS) Electrical Characteristics

over recommended operating conditions (unless otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

1.8 V MODE

VIL

Input Low Voltage

0.3 × VDD

(1)

VILSS

Input Low Voltage Steady State

0.3 × VDD

(1)

VIH

Input High Voltage

0.7 × VDD

(1)

1.98(2)

VIHSS

Input High Voltage Steady State

0.7 × VDD

(1)

VHYS

Input Hysteresis Voltage

0.1 × VDD

(1)

IIN

Input Leakage Current.

VI = 1.8 V

VI = 0 V

±10

µA

VOL

Output Low Voltage

0.2 × VDD

(1)

IOL (3)

Low Level Output Current

VOL(MAX)

SRI (5)

Input Slew Rate

18f(4)

1.8E+6

V/s

3.3 V MODE

(6)

VIL

Input Low Voltage

0.3 × VDD

(1)

VILSS

Input Low Voltage Steady State

0.25 × VDD

(1)

VIH

Input High Voltage

0.7 × VDD

(1)

3.63(2)

VIHSS

Input High Voltage Steady State

0.7 × VDD

(1)

VHYS

Input Hysteresis Voltage

0.05 × VDD

(1)

IIN

Input Leakage Current.

VI = 3.3 V

VI = 0 V

±10

µA

VOL

Output Low Voltage

0.4

IOL (3)

Low Level Output Current

VOL(MAX)

SRI (5)

Input Slew Rate

33f(4)

3.3E+6

8E+7

V/s

(1)

VDD stands for corresponding power supply. For more information on the power supply name and the corresponding ball(s), see

POWER column of the Pin Attributes table.

(2)

This value also defines the Absolute Maximum Ratings value the IO.

(3)

The IOL parameter defines the minimum Low Level Output Current for which the device is able to maintain the specified VOL value.

The value defined by this parameter should be considered the maximum current available to a system implementation which needs to

maintain the specified VOL value for attached components.

(4)

f = toggle frequency of the input signal in Hz.

(5)

This MIN parameter only applies to input signal functions which are not defined in their respective Timing and Switching

Characteristics sections. Select the MIN parameter which results in the largest value.

(6)

I2C Hs-mode is not supported when operating the IO in 3.3 V mode.

AM62A7, AM62A7-Q1, AM62A3, AM62A3-Q1

SPRSP77A – MARCH 2023 – REVISED AUGUST 2023

www.ti.com

Submit Document Feedback

Product Folder Links: AM62A7 AM62A7-Q1 AM62A3 AM62A3-Q1

AM62A7 датащи(PDF) 84 Page - Texas Instruments

AM62A7 датащи(HTML) 84 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL