| поискавой системы для электроныых деталей |
|
UCS81003 датащи(PDF) 58 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS81003 датащи(HTML) 58 Page - Microchip Technology |
|
58 / 108 page ![]() UCS81003 DS20005334A-page 58 2014 Microchip Technology Inc. 10.4.4 ATTACH DETECTION CONFIGURATION RESISTER The contents of this register are retained in Sleep. bit 2 S0_SET: In SMBus mode, enables the Attach and Removal Detection feature and affects the power state (see Section 9.2 “Active Mode Selection”). 1 = Detection is enabled. Also see Table 5-2. 0 = Detection is not enabled. Also see Table 5-2. bit 1 PWR_ENS: Controls whether the port power switch may be turned on or not and affects the power state (see Section 5.3.4 “PWR_EN Input”). This bit is OR’d with the PWR_EN pin and the polarity of both are controlled by SEL pin decode. Thus, if the polarity is set to active high, either the PWR_EN pin or this bit must be ‘1’ to enable the port power switch. bit 0 LATCHS: In SMBus mode, controls the fault handling routine that is used in the case that an error is detected (see Section 5.3.5 “Latch Input”). 1 = The UCS81003 will latch its error conditions. In order for the device to return to normal Active state, the ERR bit must be cleared by the user. 0 = The UCS81003 will automatically retry when an error condition is detected. REGISTER 10-10: SWITCH CONFIGURATION REGISTER (ADDRESS 17H) (CONTINUED) REGISTER 10-11: ATTACH DETECTION CONFIGURATION REGISTER (ADDRESS 18H) R/W-0 R/W-1 R/W-0 R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 RESERVED DISCHG_TIME_SEL<1:0> ATT_TH<1:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-4 RESERVED: Do not change. bit 3-2 DISCHG_TIME_SEL<1:0>: Sets the tDISCHARGE time as follows: 00 = 100 ms 01 = 200 ms 10 = 300 ms 11 = 400 ms bit 1-0 ATT_TH<1:0>: Determines the Attach Detection threshold (IDET_QUAL) and Removal Detection thresh- olds (IREM_QUAL_DET and IREM_QUAL_ACT) as shown below. (Note 1) 00 = 200 µA Attach, 100 µA Removal Threshold 01 = 400 µA Attach, 300 µA Removal Threshold 10 = 800 µA Attach, 700 µA Removal Threshold 11 = 1000 µA Attach, 900 µA Removal Threshold Note 1: The removal threshold is different when operating in the Active power state versus when operating in the Detect power state. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |