PIC18F242 datasheet(87/332 Pages) MICROCHIP

87 / 332 page

DS39564C-page 85

PIC18FXX2

8.6

INT0 Interrupt

External interrupts on the RB0/INT0, RB1/INT1 and

RB2/INT2 pins are edge triggered: either rising, if the

corresponding INTEDGx bit is set in the INTCON2 reg-

ister, or falling, if the INTEDGx bit is clear. When a valid

edge appears on the RBx/INTx pin, the corresponding

flag bit INTxF is set. This interrupt can be disabled by

clearing the corresponding enable bit INTxE. Flag bit

INTxF must be cleared in software in the Interrupt Ser-

vice Routine before re-enabling the interrupt. All exter-

nal interrupts (INT0, INT1 and INT2) can wake-up the

processor from SLEEP, if bit INTxE was set prior to

going into SLEEP. If the global interrupt enable bit GIE

is set, the processor will branch to the interrupt vector

following wake-up.

Interrupt priority for INT1 and INT2 is determined by the

value contained in the interrupt priority bits, INT1IP

(INTCON3<6>) and INT2IP (INTCON3<7>). There is

no priority bit associated with INT0. It is always a high

priority interrupt source.

8.7

TMR0 Interrupt

In 8-bit mode (which is the default), an overflow

(FFh

→ 00h) in the TMR0 register will set flag bit

TMR0IF. In 16-bit mode, an overflow (FFFFh

→ 0000h)

in the TMR0H:TMR0L registers will set flag bit TMR0IF.

The interrupt can be enabled/disabled by setting/

clearing enable bit T0IE (INTCON<5>). Interrupt prior-

ity for Timer0 is determined by the value contained in

the interrupt priority bit TMR0IP (INTCON2<2>). See

Section 10.0 for further details on the Timer0 module.

8.8

PORTB Interrupt-on-Change

An input change on PORTB<7:4> sets flag bit RBIF

(INTCON<0>). The interrupt can be enabled/disabled

by setting/clearing enable bit, RBIE (INTCON<3>).

Interrupt priority for PORTB interrupt-on-change is

determined by the value contained in the interrupt

priority bit, RBIP (INTCON2<0>).

8.9

Context Saving During Interrupts

During an interrupt, the return PC value is saved on the

stack. Additionally, the WREG, STATUS and BSR regis-

ters are saved on the fast return stack. If a fast return

from interrupt is not used (See Section 4.3), the user

may need to save the WREG, STATUS and BSR regis-

ters in software. Depending on the user’s application,

other registers may also need to be saved. Equation 8-1

saves and restores the WREG, STATUS and BSR

registers during an Interrupt Service Routine.

EXAMPLE 8-1:

SAVING STATUS, WREG AND BSR REGISTERS IN RAM

MOVWF

W_TEMP

; W_TEMP is in virtual bank

MOVFF

STATUS, STATUS_TEMP

; STATUS_TEMP located anywhere

MOVFF

BSR,

BSR_TEMP

; BSR located anywhere

;

; USER ISR CODE

;

MOVFF

BSR_TEMP,

BSR

; Restore BSR

MOVF

W_TEMP,

; Restore WREG

MOVFF

STATUS_TEMP,STATUS

; Restore STATUS

PIC18F242 датащи(PDF) 87 Page - Microchip Technology

PIC18F242 датащи(HTML) 87 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL