OR2C04A datasheet(28/192 Pages) ETC

28 / 192 page

Lucent Technologies Inc.

Data Sheet

ORCA Series 2 FPGAs

June 1999

Programmable Input/Output Cells

(continued)

PIC Routing Resources

The PIC routing is designed to route 4-bit wide buses

efficiently. For example, any four consecutive I/O pads

can have both their input and output signals routed into

one PLC. Using only PIC routing, either the input or

output data can be routed to/from a single PLC from/to

any eight pads in a row, as in Figure 25.

The connections between PLCs and the I/O pad are

provided by two basic types of routing resources.

These are routing resources internal to the PIC and

routing resources used for PIC-PLC connection.

Figure 26 and Figure 27 show a high-level and detailed

view of these routing resources, respectively.

5-4504(F)

Figure 25. Simplified PIC Routing Diagram

The PIC’s name is represented by a two-letter designa-

tion to indicate on which side of the device it is located

followed by a number to indicate in which row or col-

umn it is located. The first letter, P, designates that the

cell is a PIC and not a PLC. The second letter indicates

the side of the array where the PIC is located. The four

sides are left (L), right (R), top (T), and bottom (B). The

individual I/O pad is indicated by a single letter (either

A, B, C, or D) placed at the end of the PIC name. As an

example, PL10A indicates a pad located on the left

side of the array in the tenth row.

Each PIC has four pads and each pad can be config-

ured as an input, an output (3-statable), a direct output,

or a bidirectional I/O. When the pads are used as

inputs, the external signals are provided to the internal

circuitry at IN[3:0]. When the pads are used to provide

direct inputs to the latches/FFs, they are connected

through DIN[3:0]. When the pads are used as outputs,

the internal signals connect to the pads through

OUT[3:0]. When the pads are used as direct outputs,

the output from the latches/flip-flops in the PLCs to the

PIC is designated DOUT[3:0]. When the outputs are

3-statable, the 3-state enable signals are TS[3:0].

Routing Resources Internal to the PIC

For inter-PIC routing, the PIC contains 14 lines used to

route signals around the perimeter of the FPGA. Figure

25 shows these lines running vertically for a PIC

located on the left side. Figure 26 shows the lines run-

ning horizontally for a PIC located at the top of the

FPGA.

PXL Lines. Each PIC has two PXL lines, labeled

PXL[1:0]. Like the XL lines of the PLC, the PXL lines

span the entire edge of the FPGA.

PXH Lines. Each PIC has four PXH lines, labeled

PXH[3:0]. Like the XH lines of the PLC, the PXH lines

span half the edge of the FPGA.

PX2 Lines. There are four PX2 lines in each PIC,

labeled PX2[3:0]. The PX2 lines pass through two adja-

cent PICs before being broken. These are used to

route nets around the perimeter equally a distance of

two or more PICs.

PX1 Lines. Each PIC has four PX1 lines, labeled

PX1[3:0]. The PX1 lines are one PIC long and are

extended to adjacent PICs by enabling CIPs.

PAD D

I/O3

PXL

PIC

SWITCHING

MATRIX

PAD C

I/O2

PAD B

I/O1

PAD A

I/O0

PXH

PX2

PX1

PLC X4

PLC X1

PLC PSW

PLC DOUT

PLC XL

PLC XH

PLC X1

PLC X4

PLC DIN

PXL

PXH

PX2

PX1

OR2C04A датащи(PDF) 28 Page - List of Unclassifed Manufacturers

OR2C04A датащи(HTML) 28 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL