OR2C04A datasheet(27/192 Pages) ETC

27 / 192 page

Lucent Technologies Inc.

Data Sheet

June 1999

ORCA Series 2 FPGAs

Programmable Input/Output Cells

(continued)

Regardless of the power supply that the VDD5 pins are

connected to (5 V or 3.3 V), the OR2TxxA devices will

drive the pin to the 3.3 V levels when the output buffer

is enabled. If the other device being driven by the

OR2TxxA device has TTL-compatible inputs, then the

device will not dissipate much input buffer power. This

is because the OR2TxxA output is being driven to a

higher level than the TTL level required. If the other

device has a CMOS-compatible input, the amount of

input buffer power will also be small. Both of these

power values are dependent upon the input buffer char-

acteristics of the other device when driven at the

OR2TxxA output buffer voltage levels.

The 2TxxA device has internal programmable pull-ups

on the I/O buffers. These pull-up voltages are always

referenced to VDD. This means that the VDD5 voltage

has no effect on the value of the pull-up voltage at the

pad. This voltage level is always sufficient to pull the

input buffer of the 2TxxA device to a high state. The pin

on the 2TxxA device will be at a level 1.0 V below VDD

(minimum of 2.0 V with a minimum VDD of 3.0 V). This

voltage is sufficient to pull the external pin up to a 3.3 V

CMOS high-input level (1.8 V min) or a TTL high-input

level (2.0 V min) in a 5 V tolerant system, but it will

never pull the pad up to the VDD5 rail. Therefore, in a

5 V tolerant system using 5 V CMOS parts, care must

be taken to evaluate the use of these pull-ups to pull

the pin of the 2TxxA device to a typical 5 V CMOS

high-input level (2.2 V min).

For more information on 5 V tolerant I/Os, please see

ORCA®

Series 5 V Tolerant I/Os Application Note

(AP99-027FPGA), May 1999.

5 V Tolerant I/O (OR2TxxB)

The I/O on the OR2TxxB Series devices allow intercon-

nection to both 3.3 V and 5 V device (selectable on a

per-pin basis). Unlike the OR2TxxA family, when inter-

faceing into a 5 V signal, it no longer requires a VDD5

supply.

The OR2TxxB devices will drive the pin to the 3.3 V lev-

els when the output buffer is enabled. If the other

device being driven by the OR2TxxB device has TTL-

compatible inputs, then the device will not dissipate

much input buffer power. This is because the OR2TxxB

output is being driven to a higher level than the TTL

level required. If the other device has a CMOS-compat-

ible input, the amount of input buffer power will also be

small. Both of these power values are dependent upon

the input buffer characteristics of the other device when

driven at the OR2TxxB output buffer voltage levels.

The OR2TxxB device has internal programmable pull-

ups on the I/O buffers. These pull-up voltages are

always referenced to VDD and are always sufficient to

pull the input buffer of the OR2TxxB device to a high

state. The pin on the OR2TxxB device will be at a level

1.0 V below VDD (minimum of 2.0 V with a minimum

VDD of 3.0 V). This voltage is sufficient to pull the exter-

nal pin up to a 3.3 V CMOS high-input level (1.8 V, min)

or a TTL high input level (2.0 V, min) in a 5 V tolerant

system. Therefore, in a 5 V tolerant system using 5 V

CMOS parts, care must be taken to evaluate the use of

these pull-ups to pull the pin of the OR2TxxB device to

a typical 5 V CMOS high-input level (2.2 V, min).

PCI Compliant I/O

The I/O on the OR2TxxB Series devices allows compli-

ance with PCI local bus (Rev. 2.1) 5 V and 3.3 V signal-

ing environments. The signaling environment used for

each input buffer can be selected on a per-pin basis.

The selection provides the appropriate I/O clamping

diodes for PCI compliance.

OR2TxxB devices have 5 V tolerant I/Os as previously

explained, but can optionally be selected on a pin-by-

pin basis to be PCI bus 3.3 V signaling compliant (PCI

bus 5 V signaling compliance occurs in 5 V tolerant

operation mode). Inputs may have a pull-up or pull-

down resistor selected on an input for signal stabiliza-

tion and power management. Input signals in a PIO

can be passed to PIC routing on any of three paths,

two general signal paths into PIC routing, and/or a fast

route into the clock routing system.

OR2TxxA series devices are only compliant in 3.3 V

PCI Local Bus (Rev 2.1) signalling environments.

OR2CxxA devices are only compliant in 5 V PCI Local

Bus (Rev 2.1) signalling environments.

OR2C04A датащи(PDF) 27 Page - List of Unclassifed Manufacturers

OR2C04A датащи(HTML) 27 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL