TMPR4937 datasheet(33/552 Pages) TOSHIBA

33 / 552 page

3 General Safety Precautions and Usage Considerations

3-11

3.4.2

Inspection Sequence

Do not insert devices in the wrong orientation. Make sure that the positive and

negative electrodes of the power supply are correctly connected. Otherwise, the rated

maximum current or maximum power dissipation may be exceeded and the device

may break down or undergo performance degradation, causing it to catch fire or

explode, resulting in injury to the user.

When conducting any kind of evaluation, inspection or testing using AC power with a

peak voltage of 42.4 V or DC power exceeding 60 V, be sure to connect the electrodes

or probes of the testing equipment to the device under test before powering it on.

Connecting the electrodes or probes of testing equipment to a device while it is

powered on may result in electric shock, causing injury.

(1) Apply voltage to the test jig only after inserting the device securely into it. When applying or removing

power, observe the relevant precautions, if any.

(2) Make sure that the voltage applied to the device is off before removing the device from the test jig.

Otherwise, the device may undergo performance degradation or be destroyed.

(3) Make sure that no surge voltages from the measuring equipment are applied to the device.

(4) The chips housed in tape carrier packages (TCPs) are bare chips and are therefore exposed. During

inspection take care not to crack the chip or cause any flaws in it.

Electrical contact may also cause a chip to become faulty. Therefore make sure that nothing comes into

electrical contact with the chip.

3.5

Mounting

There are essentially two main types of semiconductor device package: lead insertion and surface mount. During

mounting on printed circuit boards, devices can become contaminated by flux or damaged by thermal stress

from the soldering process. With surface-mount devices in particular, the most significant problem is thermal

stress from solder reflow, when the entire package is subjected to heat. This section describes a recommended

temperature profile for each mounting method, as well as general precautions which you should take when

mounting devices on printed circuit boards. Note, however, that even for devices with the same package type,

the appropriate mounting method varies according to the size of the chip and the size and shape of the lead

frame. Therefore, please consult the relevant technical datasheet and databook.

3.5.1

Lead forming

Always wear protective glasses when cutting the leads of a device with clippers or a

similar tool. If you do not, small bits of metal flying off the cut ends may damage

your eyes.

Do not touch the tips of device leads. Because some types of device have leads with

pointed tips, you may prick your finger.

Semiconductor devices must undergo a process in which the leads are cut and formed before the devices can be

mounted on a printed circuit board. If undue stress is applied to the interior of a device during this process,

mechanical breakdown or performance degradation can result. This is attributable primarily to differences

between the stress on the device’s external leads and the stress on the internal leads. If the relative difference is

great enough, the device’s internal leads, adhesive properties or sealant can be damaged. Observe these

precautions during the lead-forming process (this does not apply to surface-mount devices):

(1) Lead insertion hole intervals on the printed circuit board should match the lead pitch of the device

precisely.

TMPR4937 датащи(PDF) 33 Page - Toshiba Semiconductor

TMPR4937 датащи(HTML) 33 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL