CS5530A datasheet(29/259 Pages) NSC

29 / 259 page

Revision 1.1

www.national.com

Signal Definitions (Continued)

SMEMW#/

FP_HSYNC_OUT

Limited ISA Mode: Flat Panel Horizontal Sync Output

Refer to Section 2.2.11 "Display Interface" on page 35 for this signal’s defini-

tion.

Note that if Limited ISA Mode of operation is selected, SMEMW# is available

on pin AF3 (multiplexed with RTCCS#).

ISA Master Mode: System Memory Write

SMEMW# is asserted for any memory write accesses below 1 MB (i.e.,

A23:A20 set to 0). This enables 8-bit memory slaves to decode the memory

address on SA[19:0].

SMEMR#/

FP_VSYNC_OUT

Limited ISA Mode: Flat Panel Vertical Sync Output

Refer to Section 2.2.11 "Display Interface" on page 35 for this signal’s defini-

tion.

Note that if Limited ISA Mode of operation is selected, SMEMR# is available

on pin AD4 (multiplexed with RTCALE).

ISA Master Mode: System Memory Read

SMEMR# is asserted for memory read accesses below 1 MB (i.e., A23:A20

set to 0). This enables 8-bit memory slaves to decode the memory address

on SA[19:0].

SMEMW#/

RTCCS#

AF3

System Memory Write / Real-Time Clock Chip Select

If Limited ISA Mode of operation has been selected, then SMEMW# can be

output on this pin. SMEMW# is asserted for any memory write accesses

below 1 MB (i.e., A23:A20 set to 0). This enables 8-bit memory slaves to

decode the memory address on SA[19:0].

RTCCS# is a chip select to an external real-time clock chip. This signal is

activated on reads or writes to I/O Port 071h.

Function selection is made through F0 Index 53h[2]: 0 = SMEMW#,

1= RTCCS#.

SMEMR#/

RTCALE

AD4

System Memory Read / Real-Time Clock Address Latch Enable

If Limited ISA Mode of operation has been selected, then SMEMR# can be

output on this pin. SMEMR# is asserted for memory read accesses below 1

MB (i.e., A23:A20 set to 0). This enables 8-bit memory slaves to decode the

memory address on SA[19:0].

RTCALE is a signal telling an external real-time clock chip to latch the

address, which is on the SD bus.

Function selection is made through F0 Index 53h[2]: 0 = SMEMR#,

1= RTCALE.

SBHE#

AE17

I/O

(PU)

System Bus High Enable

The CS5530A or ISA master asserts SBHE# to indicate that SD[15:8] will be

used to transfer a byte at an odd address.

SBHE# is an output during non-ISA master DMA operations. It is driven as

the inversion of AD0 during 8-bit DMA cycles. It is forced low for all 16-bit

DMA cycles.

SBHE# is an input during ISA master operations.

This pin is internally connected to a 20-kohm pull-up resistor.

BALE

AF9

Buffered Address Latch Enable

BALE indicates when SA[23:0] and SBHE# are valid and may be latched.

For DMA transfers, BALE remains asserted until the transfer is complete.

2.2.5

ISA Bus Interface (Continued)

Signal Name

No.

Type

Description

CS5530A датащи(PDF) 29 Page - National Semiconductor (TI)

CS5530A датащи(HTML) 29 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL