OR4E2 datasheet(44/124 Pages) AGERE

44 / 124 page

Lucent Technologies Inc.

Preliminary Data Sheet

December 2000

ORCA Series 4 FPGAs

Special Function Blocks (continued)

The TAPC generates control signals that allow capture, shift, and update operations on the instruction and data

registers. In the capture operation, data is loaded into the register. In the shift operation, the captured data is

shifted out while new data is shifted in. In the update operation, either the instruction register is loaded for instruc-

tion decode, or the boundary-scan register is updated for control of outputs.

The test host generates a test by providing input into the ORCA Series TMS input synchronous with TCK. This

sequences the TAPC through states in order to perform the desired function on the instruction register or a data

TMS input value.

5-5370(F)

Figure 28. TAP Controller State Transition Diagram

SELECT-

DR-SCAN

CAPTURE-DR

SHIFT-DR

EXIT1-DR

PAUSE-DR

EXIT2-DR

UPDATE-DR

RUN-TEST/

IDLE

TEST-LOGIC-

RESET

SELECT-

IR-SCAN

CAPTURE-IR

SHIFT-IR

EXIT1-IR

PAUSE-IR

EXIT2-IR

UPDATE-IR

Boundary-Scan Cells

Figure 29 is a diagram of the boundary-scan cell (BSC)

in the ORCA series PIOs. There are four BSCs in each

PIO: one for each pad, except as noted above. The

BSCs are connected serially to form the BSR. The

BSC controls the functionality of the in, out, and 3-state

signals for each pad.

The BSC allows the I/O to function in either the normal

or test mode. Normal mode is defined as when an out-

put buffer receives input from the PLC array and pro-

vides output at the pad or when an input buffer

provides input from the pad to the PLC array. In the test

mode, the BSC executes a boundary-scan operation,

such as shifting in scan data from an upstream BSC in

the BSR, providing test stimuli to the pad, capturing

test data at the pad, etc.

The primary functions of the BSC are shifting scan data

serially in the BSR and observing input (p_in), output

(p_out), and 3-state (p_ts) signals at the pads. The

BSC consists of two circuits: the bidirectional data cell

is used to access the input and output data, and the

direction control cell is used to access the 3-state

value. Both cells consist of a FF used to shift scan data

which feeds a FF to control the I/O buffer. The bidirec-

tional data cell is connected serially to the direction

control cell to form a boundary-scan shift register.

The TAPC signals (capture, update, shiftn, treset, and

TCK) and the MODE signal control the operation of the

BSC. The bidirectional data cell is also controlled by

the high out/low in (HOLI) signal generated by the

direction control cell. When HOLI is low, the bidirec-

tional data cell receives input buffer data into the BSC.

When HOLI is high, the BSC is loaded with functional

data from the PLC.

OR4E2 датащи(PDF) 44 Page - Agere Systems

OR4E2 датащи(HTML) 44 Page - Agere Systems

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL