MFRC63002R datasheet(29/118 Pages) NXP

29 / 118 page

MFRC630

All information provided in this document is subject to legal disclaimers.

Product data sheet

COMPANY PUBLIC

Rev. 3.1 — 6 September 2012

227531

29 of 118

NXP Semiconductors

MFRC630

Contactless reader IC

8.5

Buffer

8.5.1 Overview

An 512

 8-bit FIFO buffer is implemented in the MFRC630. It buffers the input and output

data stream between the host and the internal state machine of the MFRC630. Thus, it is

possible to handle data streams with lengths of up to 512 bytes without taking timing

constraints into account. The FIFO can also be limited to a size of 255 byte. In this case all

the parameters (FIFO length, Watermark...) require a single byte only for definition. In

case of a 512 byte FIFO length the definition of this values requires 2 bytes.

8.5.2 Accessing the FIFO buffer

When the

-Controller starts a command, the MFRC630 may, while the command is in

progress, access the FIFO-buffer according to that command. Physically only one

FIFO-buffer is implemented, which can be used in input and output direction. Therefore

the

-Controller has to take care, not to access the FIFO buffer in a way that corrupts the

FIFO data.

8.5.3 Controlling the FIFO buffer

Besides writing to and reading from the FIFO buffer, the FIFO-buffer pointers might be

reset by setting the bit FIFOFlush in FIFOControl to 1. Consequently, the FIFOLevel bits

are set to logic 0, the actually stored bytes are not accessible any more and the FIFO

buffer can be filled with another 512 bytes (or 255 bytes if the bit FIFOSize is set to 1)

again.

8.5.4 Status Information about the FIFO buffer

The host may obtain the following data about the FIFO-buffers status:

• Number of bytes already stored in the FIFO-buffer. Writing increments, reading

decrements the FIFO level: FIFOLength in register FIFOLength (and FIFOControl

• Warning, that the FIFO-buffer is almost full: HiAlert in register FIFOControl according

to the value of the water level in register WaterLevel (Register 02h bit [2], Register

03h bit[7:0])

• Warning, that the FIFO-buffer is almost empty: LoAlert in register FIFOControl

according to the value of the water level in register WaterLevel (Register 02h bit [2],

• FIFOOvl bit indicates, that bytes were written to the FIFO buffer although it was

already full: ErrIrq in register Irq0.

WaterLevel is one single value defining both HiAlert (counting from the FIFO top) and

LoAlert (counting from the FIFO bottom). The MFRC630 can generate an interrupt signal

if:

• LoAlertIRQEn in register IRQ0En is set to logic 1 it will activate pin IRQ when LoAlert

in the register FIFOControl changes to 1.

• HiAlertIRQEN in register IRQ0En is set to logic 1 it will activate pin IRQ when HiAlert

in the register FIFOControl changes to 1.

MFRC63002R датащи(PDF) 29 Page - NXP Semiconductors

MFRC63002R датащи(HTML) 29 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL