XRT86VL34 datasheet(39/156 Pages) EXAR

39 / 156 page

XRT86VL34

REV. V1.2.0

QUAD T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION

TABLE 19: SLIP BUFFER CONTROL REGISTER (SBCR)

HEX ADDRESS: 0Xn116

BIT

FUNCTION

TYPE

DEFAULT

DESCRIPTION-OPERATION

TxSB_ISFIFO

R/W

Transmit Slip Buffer Mode

This bit permits the user to configure the Transmit Slip Buffer to function as

either “Slip-Buffer” Mode, or as a “FIFO”, as depicted below.

0 - Configures the Transmit Slip Buffer to function as a “Slip-Buffer”.

1 - Configures the Transmit Slip Buffer to function as a “FIFO”.

NOTE: Transmit slip buffer is only used in high-speed or multiplexed mode

where TxSERCLKn must be configured as inputs only. Users must

make sure that the “Transmit Direction” timing (i.e. TxMSYNC) and

the TxSerClk input clock signal are synchronous to prevent any

transmit slips from occuring.

NOTE: The data latency is dictated by FIFO Latency in the FIFO Latency

6-5

Reserved

SB_FORCESF

R/W

Force Signaling Freeze

This bit permits the user to freeze any signaling update on the RxSIGn output

pin as well as the Receive Signaling Array Register -RSAR (0xn500-0xn51F)

until this bit is cleared.

0 = Signaling on RxSIG and RSAR is updated immediately.

1 = Signaling on RxSIG and RSAR is not updated until this bit is set to ‘0’.

SB_SFENB

R/W

Signal Freeze Enable Upon Buffer Slips

This bit enables signaling freeze for one multiframe after the receive buffer

slips.

If signaling freeze is enabled, then the “Receive Channel” will freeze all sig-

naling updates on RxSIG pin and RSAR (0xn500-0xn51F) for at least “one-

multiframe” period, after a “slip-event” has been detected within the “Receive

Slip Buffer”.

0 = Disables signaling freeze for one multi-frame after receive buffer slips.

1 = Enables signaling freeze for one multi-frame after receive buffer slips.

SB_SDIR

R/W

Slip Buffer (RxSync) Direction Select

This bit permits user to select the direction of the receive frame boundary

(RxSYNC) signal if the receive buffer is enabled. (i.e. SB_ENB[1:0] = 01 or

10). If slip buffer is bypassed, RxSYNC is always an output pin.

0 = Selects the RxSync signal as an output

1 = Selects the RxSync signal as an input

XRT86VL34 датащи(PDF) 39 Page - Exar Corporation

XRT86VL34 датащи(HTML) 39 Page - Exar Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL