| поискавой системы для электроныых деталей |
|
AS3543-ECTP датащи(PDF) 18 Page - ams AG |
|
|
|||||||||||||||||||||||||||||
AS3543-ECTP датащи(HTML) 18 Page - ams AG |
|
18 / 92 page ![]() www.austriamicrosystems.com Revision 1.11 17 - 91 AS3543 3v2 Data Sheet - D e t a i l e d D e s c r i p t i o n - A u d i o F u n c t i o n s 8.1.3 Register Description Line input has to be enabled in register 14h first before other settings in register 0Ah and 0Bh can be programmed. 8.2 Microphone Input 8.2.1 General The AFE offers one microphone input and one low noise microphone voltage supply (microphone bias), voice activa- tion, microphone connect detection and push button remote control. Figure 4. Microphone Input 8.2.2 Gain Stage & Limiter The integrated pre-amplifier allows 3 preset gain settings. There is also a limiter which attenuates high input signals from e.g. electret microphones signal to 1Vp. The AGC has 128 steps with 0.375dB with a dynamic range of the full pre-amplifier level. The AGC is ON by default but can be disabled by a microphone register bit. Apart from the microphone pre-amplifier the microphone input signal can further be amplified with 32 @1.5dB pro- grammable logarithmic gain steps and MUTE. All gains and MUTE are independently programmable. The gain can be set from –40.5dB to +6dB. The stage features a soft-start function. Pre-amplifier and gain-stage settings can be set before enabling the micro- phone stage. After enabling the stage to gain is automatically set to the defined value by using the 128 steps of the AGC. 8.2.3 Supply & Detection Each microphone input generates a supply voltage of 1.5V above HPCM. The supply is designed for ≤2mA and has a 6.5mA current limit. In OFF mode the MICS terminal is pulled to AVDD with 20kOhm. A current of typically 50uA gen- erates an interrupt to inform the CPU, that a circuit is connected. When using HPCM as headset ground the HP–stage gives the interrupt. After enabling the HP-stage through the CPU the microphone detection interrupt will follow. When using the MICS terminal as ADC-10 input to monitor external voltages the 20kOhm pull-up has to be disabled by disabling the interrupt for microphone detection. Table 8. Line Input Related Register Name Base Offset Description LINE_IN_R 2-wire serial 0Ah Right Line Input 1/2 settings, Line Input 2 selection LINE_IN_L 2-wire serial 0Bh Left Line Input 1/2 settings AudioSet1 2-wire serial 14h Enable/disable driver stage AudioSet3 2-wire serial 16h Enable/disable mixer input |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |