18F8680 datasheet(25/496 Pages) MICROCHIP

25 / 496 page

 2004 Microchip Technology Inc.

DS30491C-page 23

PIC18F6585/8585/6680/8680

2.0

OSCILLATOR

CONFIGURATIONS

2.1

Oscillator Types

The PIC18F6585/8585/6680/8680 devices can be

operated in eleven different oscillator modes. The user

can program four configuration bits (FOSC3, FOSC2,

FOSC1 and FOSC0) to select one of these eleven

modes:

Low-Power Crystal

Crystal/Resonator

High-Speed Crystal/Resonator

External Resistor/Capacitor

External Clock

ECIO

External Clock with I/O

pin enabled

HS+PLL

High-Speed Crystal/Resonator

with PLL enabled

RCIO

External Resistor/Capacitor with

I/O pin enabled

ECIO+SPLL External Clock with software

controlled PLL

10. ECIO+PLL

External Clock with PLL and I/O

pin enabled

11. HS+SPLL

High-Speed Crystal/Resonator

with software control

2.2

Crystal Oscillator/Ceramic

Resonators

In XT, LP, HS, HS+PLL or HS+SPLL Oscillator modes,

a crystal or ceramic resonator is connected to the OSC1

and OSC2 pins to establish oscillation. Figure 2-1

shows the pin connections.

The PIC18F6585/8585/6680/8680 oscillator design

requires the use of a parallel cut crystal.

FIGURE 2-1:

CRYSTAL/CERAMIC

RESONATOR OPERATION

(HS, XT OR LP

CONFIGURATION)

TABLE 2-1:

CAPACITOR SELECTION FOR

CERAMIC RESONATORS

Note:

Use of a series cut crystal may give a fre-

quency out of the crystal manufacturers

specifications.

Ranges Tested:

Mode

Freq

455 kHz

2.0 MHz

4.0 MHz

68-100 pF

15-68 pF

68-100 pF

15-68 pF

8.0 MHz

16.0 MHz

10-68 pF

10-22 pF

10-68 pF

10-22 pF

These values are for design guidance only.

See notes following this table.

Resonators Used:

2.0 MHz

Murata Erie CSA2.00MG

± 0.5%

4.0 MHz

Murata Erie CSA4.00MG

± 0.5%

8.0 MHz

Murata Erie CSA8.00MT

± 0.5%

16.0 MHz Murata Erie CSA16.00MX

± 0.5%

All resonators used did not have built-in capacitors.

Note 1: Higher capacitance increases the stability

of the oscillator, but also increases the

start-up time.

2: When operating below 3V VDD, or when

using certain ceramic resonators at any

voltage, it may be necessary to use high

gain HS mode, try a lower frequency

resonator, or switch to a crystal oscillator.

3: Since each resonator/crystal has its own

characteristics, the user should consult the

resonator/crystal manufacturer for appro-

priate values of external components, or

verify oscillator performance.

Note 1:

See Table 2-1 and Table 2-2 for recommended

values of C1 and C2.

A series resistor (RS) may be required for AT

strip cut crystals.

RF varies with the oscillator mode chosen.

C1(1)

C2(1)

XTAL

OSC2

OSC1

(3)

Sleep

Logic

PIC18FXX80/XX85

RS(2)

Internal

18F8680 датащи(PDF) 25 Page - Microchip Technology

18F8680 датащи(HTML) 25 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL